REV. 1.1.3 EFR[5]: Special Character Detect Enable Lo" />
參數資料
型號： XR16L2550IJ-F
廠商： Exar Corporation
文件頁數： 26/44頁
文件大?。?/td> 0K
描述： IC UART FIFO 16B DUAL 44PLCC
標準包裝： 27
特點： *
通道數： 2，DUART
FIFO's： 16 字節
規程： RS232
電源電壓： 2.25 V ~ 5.5 V
帶自動流量控制功能： 是
帶IrDA 編碼器/解碼器： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 44-LCC（J 形引線）
供應商設備封裝： 44-PLCC（16.59x16.59）
包裝： 管件
XR16L2550
32
LOW VOLTAGE DUART WITH 16-BYTE FIFO
REV. 1.1.3
EFR[5]: Special Character Detect Enable
Logic 0 = Special Character Detect Disabled (default).
Logic 1 = Special Character Detect Enabled. The UART compares each incoming receive character with
data in Xoff-2 register. If a match exists, the receive data will be transferred to FIFO and ISR bit-4 will be set
to indicate detection of the special character. Bit-0 corresponds with the LSB bit of the receive character. If
flow control is set for comparing Xon1, Xoff1 (EFR [1:0]= ‘10’) then flow control and special character work
normally. However, if flow control is set for comparing Xon2, Xoff2 (EFR[1:0]= ‘01’) then flow control works
normally, but Xoff2 will not go to the FIFO, and will generate an Xoff interrupt and a special character
interrupt, if enabled via IER bit-5. Special character interrupts are cleared automatically after the next
received character.
EFR[6]: Auto RTS Flow Control Enable
RTS# output may be used for hardware flow control by setting EFR bit-6 to logic 1. When Auto RTS is
selected, an interrupt will be generated when the receive FIFO is filled to the programmed trigger level and
RTS de-asserts to a logic 1 at the next upper trigger level. RTS# will return to a logic 0 when FIFO data falls
below the next lower trigger level. The RTS# output must be asserted (logic 0) before the auto RTS can take
effect. RTS# pin will function as a general purpose output when hardware flow control is disabled.
Logic 0 = Automatic RTS flow control is disabled (default).
Logic 1 = Enable Automatic RTS flow control.
EFR[7]: Auto CTS Flow Control Enable
Automatic CTS Flow Control.
Logic 0 = Automatic CTS flow control is disabled (default).
Logic 1 = Enable Automatic CTS flow control. Data transmission stops when CTS# input de-asserts to logic
1. Data transmission resumes when CTS# returns to a logic 0.
4.15
Software Flow Control Registers (XOFF1, XOFF2, XON1, XON2) - Read/Write
These registers are used as the programmable software flow control characters XOFF1, XOFF2, XON1, and
XON2. For more details, see Table 6.
相關PDF資料
PDF描述
XR16L2551IM-F IC UART FIFO 16B DUAL 48TQFP
XR16L2552IJ-F IC UART FIFO 16B DUAL 44PLCC
XR16L2750IJ-F IC UART FIFO 64B DUAL 44PLCC
XR16L2751CMTR-F IC UART FIFO 64B DUAL 48TQFP
XR16L2752CJ-F IC UART FIFO 64B DUAL 44PLCC
相關代理商/技術參數
參數描述
XR16L2550IL 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16L2550IL-0A-EB 功能描述:UART 接口集成電路 Supports L2550 32pin QFN, ISA Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16L2550IL-0B-EB 功能描述:UART 接口集成電路 Supports L2550 32pin QFN, PCI Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16L2550IL-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16L2550ILTR-F 制造商:Exar Corporation 功能描述:UART 2-CH 16Byte FIFO 2.5V/3.3V/5V 32-Pin QFN EP T/R 制造商:Exar Corporation 功能描述:XR16L2550ILTR-F
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*