- 您現在的位置：買賣IC網 > PDF目錄376454 > XR16L2550IL (EXAR CORP) LOW VOLTAGE DUART WITH 16-BYTE FIFO PDF資料下載
參數資料
| 型號： | XR16L2550IL |
| 廠商： | EXAR CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | LOW VOLTAGE DUART WITH 16-BYTE FIFO |
| 中文描述： | 2 CHANNEL(S), 3.125M bps, SERIAL COMM CONTROLLER, QCC32 |
| 封裝： | 5 X 5 MM, 0.90 MM HEIGHT, QFN-32 |
| 文件頁數： | 22/45頁 |
| 文件大?。?/td> | 278K |
| 代理商： | XR16L2550IL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁
XR16L2550
LOW VOLTAGE DUART WITH 16-BYTE FIFO
á
REV. 1.0.0
22
The Interrupt Enable Register (IER) masks the interrupts from receive data ready, transmit empty, line status
and modem status registers. These interrupts are reported in the Interrupt Status Register (ISR).
3.3.1
IER versus Receive FIFO Interrupt Mode Operation
When the receive FIFO (FCR BIT-0 = 1) and receive interrupts (IER BIT-0 = 1) are enabled, the RHR interrupts
(see ISR bits 2 and 3) status will reflect the following:
A.
The receive data available interrupts are issued to the host when the FIFO has reached the programmed
trigger level. It will be cleared when the FIFO drops below the programmed trigger level.
B.
FIFO level will be reflected in the ISR register when the FIFO trigger level is reached. Both the ISR register
status bit and the interrupt will be cleared when the FIFO drops below the trigger level.
C.
The receive data ready bit (LSR BIT-0) is set as soon as a character is transferred from the shift register to
the receive FIFO. It is reset when the FIFO is empty.
3.3.2
IER versus Receive/Transmit FIFO Polled Mode Operation
When FCR BIT-0 equals a logic 1 for FIFO enable; resetting IER bits 0-3 enables the XR16L2550 in the FIFO
polled mode of operation. Since the receiver and transmitter have separate bits in the LSR either or both can
be used in the polled mode by selecting respective transmit or receive control bit(s).
A.
LSR BIT-0 indicates there is data in RHR
or
RX FIFO.
B.
LSR BIT-1 indicates an overrun error has occurred and that data in the FIFO may not be valid.
C.
LSR BIT 2-4 provides the type of receive data errors encountered for the data byte in RHR, if any.
D.
LSR BIT-5 indicates Transmit FIFO is empty.
E.
LSR BIT-6 indicates when both the transmit FIFO and TSR are empty.
F.
LSR BIT-7 indicates a data error in at least one character in the RX FIFO.
相關PDF資料 |
PDF描述 |
|---|---|
| XR16L2550IM | LOW VOLTAGE DUART WITH 16-BYTE FIFO |
| XR16L2550 | LOW VOLTAGE DUART WITH 16-BYTE FIFO |
| XR16L2551 | LOW VOLTAGE DUART WITH POWERSAVE |
| XR16L2551IL | LOW VOLTAGE DUART WITH POWERSAVE |
| XR16L2551IM | LOW VOLTAGE DUART WITH POWERSAVE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16L2550IL-0A-EB | 功能描述:UART 接口集成電路 Supports L2550 32pin QFN, ISA Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16L2550IL-0B-EB | 功能描述:UART 接口集成電路 Supports L2550 32pin QFN, PCI Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16L2550IL-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16L2550ILTR-F | 制造商:Exar Corporation 功能描述:UART 2-CH 16Byte FIFO 2.5V/3.3V/5V 32-Pin QFN EP T/R 制造商:Exar Corporation 功能描述:XR16L2550ILTR-F |
| XR16L2550IM | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。