參數資料
型號： XR16L2750CJ
廠商： EXAR CORP
元件分類： 微控制器/微處理器
英文描述： 2.25V TO 5.5V DUART WITH 64-BYTE FIFO
中文描述： 2 CHANNEL(S), 6.25M bps, SERIAL COMM CONTROLLER, PQCC44
封裝： PLASTIC, LCC-44
文件頁數： 4/49頁
文件大?。?/td> 602K
代理商： XR16L2750CJ
á
XR16L2750
2.25V TO 5.5V DUART WITH 64-BYTE FIFO
REV. 1.0.0
4
MODEM OR SERIAL I/O INTERFACE
TXA
13
7
O
UART channel A Transmit Data or infrared encoder data. Standard
transmit and receive interface is enabled when MCR[6] = 0. In this
mode, the TX signal will be a logic 1 during reset or idle (no data). Infra-
red IrDA transmit and receive interface is enabled when MCR[6] = 1. In
the Infrared mode, the inactive state (no data) for the Infrared encoder/
decoder interface is a logic 0. If it is not used, leave it unconnected.
RXA
11
5
I
UART channel A Receive Data or infrared receive data. Normal receive
data input must idle at logic 1 condition. The infrared receiver pulses
typically idles at logic 0 but can be inverted by software control prior
going in to the decoder, see MCR[6] and FCTR[2]. If this pin is not
used, tie it to VCC or pull it high via a 100k ohm resistor.
RTSA#
36
33
O
UART channel A Request-to-Send (active low) or general purpose out-
put. This output must be asserted prior to using auto RTS flow control,
see EFR[6], MCR[1], FCTR[1:0], EMSR[5:4] and IER[6]. For auto
RS485 half-duplex direction control, see FCTR[3] and EMSR[3].
CTSA#
40
38
I
UART channel A Clear-to-Send (active low) or general purpose input.
It can be used for auto CTS flow control, see EFR[7], and IER[7]. This
input should be connected to VCC when not used.
DTRA#
37
34
O
UART channel A Data-Terminal-Ready (active low) or general purpose
output. If it is not used, leave it unconnected.
DSRA#
41
39
I
UART channel A Data-Set-Ready (active low) or general purpose input.
This input should be connected to VCC when not used. This input has
no effect on the UART.
CDA#
42
40
I
UART channel A Carrier-Detect (active low) or general purpose input.
This input should be connected to VCC when not used. This input has
no effect on the UART.
RIA#
43
41
I
UART channel A Ring-Indicator (active low) or general purpose input.
This input should be connected to VCC when not used. This input has
no effect on the UART.
OP2A#
35
32
O
Output Port 2 Channel A - The output state is defined by the user and
through the software setting of MCR[3]. INTA is set to the active mode
and OP2A# output to a logic 0 when MCR[3] is set to a logic 1. INTA is
set to the three state mode and OP2A# to a logic 1 when MCR[3] is set
to a logic 0. See MCR[3]. This output should not be used as a general
output else it will disturb the INTA output functionality.
TXB
14
8
O
UART channel B Transmit Data or infrared encoder data. Standard
transmit and receive interface is enabled when MCR[6] = 0. In this
mode, the TX signal will be a logic 1 during reset or idle (no data). Infra-
red IrDA transmit and receive interface is enabled when MCR[6] = 1. In
the Infrared mode, the inactive state (no data) for the Infrared encoder/
decoder interface is a logic 0. If it is not used, leave it unconnected.
Pin Description
N
AME
44-PLCC
P
IN
#
48-TQFP
P
IN
#
T
YPE
D
ESCRIPTION
相關PDF資料
PDF描述
XR16L2750CM 2.25V TO 5.5V DUART WITH 64-BYTE FIFO
XR16L2750IJ 2.25V TO 5.5V DUART WITH 64-BYTE FIFO
XR16L2750IM 2.25V TO 5.5V DUART WITH 64-BYTE FIFO
XR16L2750 2.25V TO 5.5V DUART WITH 64-BYTE FIFO
XR16L2751 2.25V TO 5.5V DUART WITH 64-BYTE FIFO AND POWERSAVE
相關代理商/技術參數
參數描述
XR16L2750CJ-0A-EB 功能描述:UART 接口集成電路 Supports L2750 44 ld PLCC, ISA Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16L2750CJ-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16L2750CM 制造商:EXAR 制造商全稱:EXAR 功能描述:2.25V TO 5.5V DUART WITH 64-BYTE FIFO
XR16L2750CM-0A-EB 功能描述:界面開發工具 Supports L2750 48 ld TQFP, ISA Interface RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
XR16L2750CM-0B-EB 功能描述:UART 接口集成電路 Supports L2750 48 ld TQFP, PCI Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*