參數資料
型號: XR16L580
廠商: Exar Corporation
英文描述: SMALLEST 2.25V TO 5.5V UART WITH 16-BYTE FIFO AND POWERSAVE
中文描述: 2.25V至5.5V的最小的16字節(jié)FIFO和省電的UART
文件頁數: 3/47頁
文件大?。?/td> 285K
代理商: XR16L580
á
REV. 1.2.0
XR16L580
SMALLEST 2.25V TO 5.5V UART WITH 16-BYTE FIFO AND POWERSAVE
3
PIN DESCRIPTIONS
Pin Descriptions
N
AME
32-QFN
P
IN
#
48-TQFP
PIN#
T
YPE
D
ESCRIPTION
DATA BUS INTERFACE
A2
A1
A0
D7
D6
D5
D4
D3
D2
D1
D0
IOR#
(NC)
17
18
19
5
4
3
1
32
31
30
29
14
26
27
28
4
3
2
47
46
45
44
43
19
I
Address data lines [2:0]. These 3 address lines select one of the internal regis-
ters in UART channel A/B during a data bus transaction.
I/O
Data bus lines [7:0] (bidirectional).
I
When 16/68# pin is at logic 1, the Intel bus interface is selected and this input
becomes read strobe (active low). The falling edge instigates an internal read
cycle and retrieves the data byte from an internal register pointed by the address
lines [A2:A0], puts the data byte on the data bus to allow the host processor to
read it on the rising edge.
When 16/68# pin is at logic 0, the Motorola bus interface is selected and this
input is not used.
IOW#
(R/W#)
12
16
I
When 16/68# pin is at logic 1, it selects Intel bus interface and this input
becomes write strobe (active low). The falling edge instigates the internal write
cycle and the rising edge transfers the data byte on the data bus to an internal
register pointed by the address lines.
When 16/68# pin is at logic 0, the Motorola bus interface is selected and this
input becomes read (logic 1) and write (logic 0) signal.
CS#
8
11
I
This input is chip select (active low) to enable the device.
INT
(IRQ#)
20
30
O
(OD)
When 16/68# pin is at logic 1 for Intel bus interface, this output become the active
high device interrupt output. The output state is defined by the user through the
software setting of MCR[3]. INT is set to the active mode when MCR[3] is set to a
logic 1. INT is set to the three state mode when MCR[3] is set to a logic 0. See
MCR[3].
When 16/68# pin is at logic 0 for Motorola bus interface, this output becomes the
active low device interrupt output (open drain). An external pull-up resistor is
required for proper operation.
MODEM OR SERIAL I/O INTERFACE
TX
7
8
O
UART Transmit Data or infrared encoder data. Standard transmit and receive
interface is enabled when MCR[6] = 0. In this mode, the TX signal will be a logic
1 during reset or idle (no data). Infrared IrDA transmit and receive interface is
enabled when MCR[6] = 1. In the Infrared mode, the inactive state (no data) for
the Infrared encoder/decoder interface is a logic 0. If it is not used, leave it
unconnected.
RX
6
7
I
UART Receive Data or infrared receive data. Normal receive data input must idle
at logic 1 condition. The infrared receiver idles at logic 0.
相關PDF資料
PDF描述
XR16L580IL SMALLEST 2.25V TO 5.5V UART WITH 16-BYTE FIFO AND POWERSAVE
XR16L580IM SMALLEST 2.25V TO 5.5V UART WITH 16-BYTE FIFO AND POWERSAVE
XR16L651 2.5V, 3.3V and 5V Low Power UART with 32-Byte FIFO(2.5V, 3.3V和5V 低功耗通用異步接收器/發(fā)送器(帶32字節(jié)先進先出))
XR16L784 HIGH PERFORMANCE 2.97V TO 5.5V QUAD UART
XR16L78464-TQFP HIGH PERFORMANCE 2.97V TO 5.5V QUAD UART
相關代理商/技術參數
參數描述
XR16L580_07 制造商:EXAR 制造商全稱:EXAR 功能描述:SMALLEST 2.25V TO 5.5V UART WITH 16-BYTE FIFO AND POWERSAVE
XR16L580IL 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16L580IL-0A-EVB 功能描述:UART 接口集成電路 Supports L580 32 pin QFN, ISA Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16L580IL-0B-EVB 功能描述:UART 接口集成電路 Supports L580 32 pin QFN, PCI Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16L580IL24 功能描述:UART 接口集成電路 UART w/ POWER SAVE RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel