參數資料
型號: XR16L784CV
廠商: EXAR CORP
元件分類: 微控制器/微處理器
英文描述: HIGH PERFORMANCE 2.97V TO 5.5V QUAD UART
中文描述: 4 CHANNEL(S), 6.25M bps, SERIAL COMM CONTROLLER, PQFP64
封裝: 10 X 10 MM, 1.40 MM HEIGHT, LQFP-64
文件頁數: 15/52頁
文件大?。?/td> 625K
代理商: XR16L784CV
á
REV. 1.2.0
XR16L784
HIGH PERFORMANCE 2.97V TO 5.5V QUAD UART
15
2.13
The auto RS485 half-duplex direction control changes the behavior of the transmitter when enabled by FCTR
bit-5. It asserts RTS# or DTR# (LOW) after a specified delay indicated in MSR[7:4] following
the last stop bit of
the last character that has been transmitted. This helps in turning around the transceiver to receive the remote
station’s response. The delay optimizes the time needed for the last transmission to reach the farthest station
on a long cable network before switching off the line driver. This delay prevents undesirable line signal
disturbance that causes signal degradation. When the host is ready to transmit next polling data packet again,
it only has to load data bytes to the transmit FIFO. The transmitter automatically de-asserts RTS# or DTR#
output (HIGH) prior to sending the data. The auto RS485 half-duplex direction control also changes the
transmitter empty interrupt to TSR empty instead of THR empty.
2.14
Infrared Mode
Each UART in the 784 includes the infrared encoder and decoder compatible to the IrDA (Infrared Data
Association) version 1.0. The input pin ENIR conveniently activates all 8 UART channels to start up in the
infrared mode. Note that the ENIR pin is sampled when the RST# input is de-asserted. This global control pin
enables the MCR bit-6 function in every UART channel register. After power up or a reset, the software can
overwrite MCR bit-6 if so desired. ENIR and MCR bit-6 also disable the receiver while the transmitter is
sending data. This prevents echoed data from reaching the receiver. The global activation ENIR pin prevents
the infrared emitter from turning on and drawing large amount of current while the system is starting up. When
the infrared feature is enabled, the transmit data outputs, TX[3:0], would idle at logic zero level. Likewise, the
RX [3:0] inputs assume an idle level of logic zero.
The infrared encoder sends out a
3/16 of a bit wide HIGH-pulse for each “0” bit in the transmit data stream.
This signal encoding reduces the on-time of the infrared LED, hence reduces the power consumption. See
Figure 11
.
The infrared decoder receives the input pulse from the infrared sensing diode on RX pin. Each time it senses a
light pulse, it returns a logic zero to the data bit stream. The decoder also accepts (when FCTR bit-4 = 1) an
inverted IR-encoded input signal. This option supports active low instead of normal active high pulse from
some infrared modules on the market.
Auto RS485 Half-duplex Control
相關PDF資料
PDF描述
XR16L784IV HIGH PERFORMANCE 2.97V TO 5.5V QUAD UART
XR16L788 HIGH PERFORMANCE OCTAL UART
XR16L788CQ HIGH PERFORMANCE OCTAL UART
XR16L788IQ HIGH PERFORMANCE OCTAL UART
XR17C154 Tip, Offset Tapered Needle, 1mm Diameter
相關代理商/技術參數
參數描述
XR16L784CV-0A-EVB 功能描述:UART 接口集成電路 Supports L784 64 ld TQFP, ISA Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16L784CV-0B-EVB 功能描述:UART 接口集成電路 Supports L784 64 ld TQFP, PCI Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16L784CV-F 功能描述:UART 接口集成電路 2.97V-5.5V 64B FIFO temp 0C to 70C RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16L784CVTR-F 功能描述:UART 接口集成電路 3.3V QUAD UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16L784IV 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE 2.97V TO 5.5V QUAD UART