- 您現在的位置：買賣IC網 > PDF目錄376454 > XR16L784IV (EXAR CORP) HIGH PERFORMANCE 2.97V TO 5.5V QUAD UART PDF資料下載
參數資料
| 型號： | XR16L784IV |
| 廠商： | EXAR CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | HIGH PERFORMANCE 2.97V TO 5.5V QUAD UART |
| 中文描述： | 4 CHANNEL(S), 6.25M bps, SERIAL COMM CONTROLLER, PQFP64 |
| 封裝： | 10 X 10 MM, 1.40 MM HEIGHT, LQFP-64 |
| 文件頁數： | 34/52頁 |
| 文件大小： | 625K |
| 代理商： | XR16L784IV |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁當前第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
XR16L784
HIGH PERFORMANCE 2.97V TO 5.5V QUAD UART
á
REV. 1.2.0
34
4.8
This register provides the status of data transfers between the UART and the host. If IER bit-2 is set to a logic
1, an LSR interrupt will be generated immediately when any character in the RX FIFO has an error (parity,
framing, overrun, break).
LSR[0]: Receive Data Ready Indicator
Logic 0 = No data in receive holding register or FIFO (default).
Logic 1 = Data has been received and is saved in the receive holding register or FIFO.
LSR[1]: Receiver Overrun Flag
Logic 0 = No overrun error (default).
Logic 1 = Overrun error. A data overrun error condition occurred in the receive shift register. This happens
when additional data arrives while the FIFO is full. In this case the previous data in the receive shift register
is overwritten. Note that under this condition the data byte in the receive shift register is not transferred into
the FIFO, therefore the data in the FIFO is not corrupted by the error.
LSR[2]: Receive Data Parity Error Flag
Logic 0 = No parity error (default).
Logic 1 = Parity error. The receive character in RHR does not have correct parity information and is suspect.
This error is associated with the character available for reading in RHR.
LSR[3]: Receive Data Framing Error Flag
Logic 0 = No framing error (default).
Logic 1 = Framing error. The receive character did not have a valid stop bit(s). This error is associated with
the character available for reading in RHR.
LSR[4]: Receive Break Flag
Logic 0 = No break condition (default).
Logic 1 = The receiver received a break signal (RX was a logic 0 for one character frame time). In the FIFO
mode, only one break character is loaded into the FIFO. The break indication remains until the RX input
returns to the idle condition, “mark” or logic 1.
LSR[5]: Transmit Holding Register Empty Flag
This bit is the Transmit Holding Register Empty indicator. This bit indicates that the transmitter is ready to
accept a new character for transmission. In addition, this bit causes the UART to issue an interrupt to the host
when the THR interrupt enable is set. The THR bit is set to a logic 1 when the last data byte is transferred from
the transmit holding register to the transmit shift register. The bit is reset to logic 0 concurrently with the data
loading to the transmit holding register by the host. In the FIFO mode this bit is set when the transmit FIFO is
empty; it is cleared when at least 1 byte is written to the transmit FIFO.
LSR[6]: Transmit Shift Register Empty Flag
This bit is the Transmit Shift Register Empty indicator. This bit is set to a logic 1 whenever the transmitter goes
idle. It is set to logic 0 whenever either the THR or TSR contains a data character. In the FIFO mode this bit is
set to one whenever the transmit FIFO and transmit shift register are both empty.
LSR[7]: Receive FIFO Data Error Flag
Logic 0 = No FIFO error (default).
Logic 1 = An indicator for the sum of all error bits in the RX FIFO. At least one parity error, framing error or
break indication is in the FIFO data. This bit clears when there is no more error(s) in the FIFO.
4.9
Modem Status Register (MSR) - Read Only
This register provides the current state of the modem interface signals, or other peripheral device that the
UART is connected. Lower four bits of this register are used to indicate the changed information. These bits
are set to a logic 1 whenever a signal from the modem changes state. These bits may be used as general
purpose inputs/outputs when they are not used with modem signals.
Line Status Register (LSR) - Read Only
相關PDF資料 |
PDF描述 |
|---|---|
| XR16L788 | HIGH PERFORMANCE OCTAL UART |
| XR16L788CQ | HIGH PERFORMANCE OCTAL UART |
| XR16L788IQ | HIGH PERFORMANCE OCTAL UART |
| XR17C154 | Tip, Offset Tapered Needle, 1mm Diameter |
| XR17C154CV | Burner |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16L784IV-F | 功能描述:UART 接口集成電路 2.97V-5.5V 64B FIFO temp -45 to 85C RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16L784IVTR-F | 功能描述:UART 接口集成電路 PCI BUS QUAD UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16L788 | 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE OCTAL UART |
| XR16L788_05 | 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE 2.97V TO 5.5V OCTAL UART |
| XR16L788_08 | 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE 2.97V TO 5.5V OCTAL UART |
發布緊急采購，3分鐘左右您將得到回復。