參數資料
型號: XR16M554IV80-F
廠商: Exar Corporation
文件頁數: 4/46頁
文件大小: 0K
描述: IC UART FIFO 16B QUAD 80LQFP
標準包裝: 119
特點: *
通道數: 4,QUART
FIFO's: 16 字節
規程: RS232
電源電壓: 1.62 V ~ 3.63 V
帶自動流量控制功能:
帶故障啟動位檢測功能:
帶調制解調器控制功能:
帶CMOS:
安裝類型: 表面貼裝
封裝/外殼: 80-LQFP
供應商設備封裝: 80-LQFP(12x12)
包裝: 托盤
XR16M554/554D
12
1.62V TO 3.63V QUAD UART WITH 16-BYTE FIFO
REV. 1.0.0
2.4
Channels A-D Internal Registers
Each UART channel in the M554 has a set of enhanced registers for controlling, monitoring and data loading
and unloading. The configuration register set is compatible to those already available in the standard single
16C550. These registers function as data holding registers (THR/RHR), interrupt status and control registers
(ISR/IER), a FIFO control register (FCR), receive line status and control registers (LSR/LCR), modem status
and control registers (MSR/MCR), programmable data rate (clock) divisor registers (DLL/DLM), and a user
accessible scratchpad register (SPR). All the register functions are discussed in full detail later in “Section 3.0,
2.5
INT Ouputs for Channels A-D
The interrupt outputs change according to the operating mode and enhanced features setup. Table 3 and 4
summarize the operating behavior for the transmitter and receiver. Also see Figure 18 through 23.
2.6
DMA Mode
The device does not support direct memory access. The DMA Mode (a legacy term) in this document does not
mean “direct memory access” but refers to data block transfer operation. The DMA mode affects the state of
the RXRDY# A-D and TXRDY# A-D output pins. The transmit and receive FIFO trigger levels provide
additional flexibility to the user for block mode operation. The LSR bits 5-6 provide an indication when the
transmitter is empty or has an empty location(s) for more data. The user can optionally operate the transmit
and receive FIFO in the DMA mode (FCR bit-3 = 1). When the transmit and receive FIFOs are enabled and the
DMA mode is disabled (FCR bit-3 = 0), the M554 is placed in single-character mode for data transmit or
receive operation. When DMA mode is enabled (FCR bit-3 = 1), the user takes advantage of block mode
operation by loading or unloading the FIFO in a block sequence determined by the programmed trigger level.
The following table show their behavior. Also see Figure 18 through 23.
TABLE 3: INT PIN OPERATION FOR TRANSMITTER FOR CHANNELS A-D
FCR BIT-0 = 0
(FIFO DISABLED)
FCR BIT-0 = 1 (FIFO ENABLED)
FCR Bit-3 = 0
(DMA Mode Disabled)
FCR Bit-3 = 1
(DMA Mode Enabled)
INT Pin
LOW = a byte in THR
HIGH = THR empty
LOW = FIFO above trigger level
HIGH = FIFO below trigger level or
FIFO empty
LOW = FIFO above trigger level
HIGH = FIFO below trigger level or
FIFO empty
TABLE 4: INT PIN OPERATION FOR RECEIVER FOR CHANNELS A-D
FCR BIT-0 = 0
(FIFO DISABLED)
FCR BIT-0 = 1 (FIFO ENABLED)
FCR Bit-3 = 0
(DMA Mode Disabled)
FCR Bit-3 = 1
(DMA Mode Enabled)
INT Pin
LOW = no data
HIGH = 1 byte
LOW = FIFO below trigger level
HIGH = FIFO above trigger level
LOW = FIFO below trigger level
HIGH = FIFO above trigger level
相關PDF資料
PDF描述
MS27497E12A8P CONN RCPT 8POS WALL MNT W/PINS
VI-JWK-IW-F1 CONVERTER MOD DC/DC 40V 100W
ATMEGA164P-B15MZ IC MCU 8BIT 16KB FLASH 44VQFN
XR68C681J-F IC UART CMOS DUAL 44PLCC
MS27497T20B35P CONN RCPT 79POS WALL MNT W/PINS
相關代理商/技術參數
參數描述
XR16M564 制造商:EXAR 制造商全稱:EXAR 功能描述:1.62V TO 3.63V QUAD UART WITH 32-BYTE FIFO
XR16M564D 制造商:EXAR 制造商全稱:EXAR 功能描述:1.62V TO 3.63V QUAD UART WITH 32-BYTE FIFO
XR16M564DIV-0A-EVB 功能描述:界面開發工具 Eval Board for XR16M564DIV-0A RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
XR16M564DIV-0B-EVB 功能描述:界面開發工具 Eval Board for XR16M564DIV-0B RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
XR16M564DIV64 制造商:EXAR 制造商全稱:EXAR 功能描述:1.62V TO 3.63V QUAD UART WITH 32-BYTE FIFO