參數資料
型號： XR16M654IV-0B-EVB
廠商： Exar Corporation
文件頁數： 30/58頁
文件大?。?/td> 0K
描述： EVAL BOARD FOR XR16M654-B 64LQFP
標準包裝： 1
系列： *
XR16M654/654D
36
1.62V TO 3.63V QUAD UART WITH 64-BYTE FIFO
REV. 1.0.0
4.8
Line Status Register (LSR) - Read Only
This register provides the status of data transfers between the UART and the host. If IER bit-2 is enabled, LSR
bit 1 will generate an interrupt immediately and LSR bits 2-4 will generate an interrupt when a character with an
error is in the RHR.
LSR[0]: Receive Data Ready Indicator
Logic 0 = No data in receive holding register or FIFO (default).
Logic 1 = Data has been received and is saved in the receive holding register or FIFO.
LSR[1]: Receiver Overrun Flag
Logic 0 = No overrun error (default).
Logic 1 = Overrun error. A data overrun error condition occurred in the receive shift register. This happens
when additional data arrives while the FIFO is full. In this case the previous data in the receive shift register
is overwritten. Note that under this condition the data byte in the receive shift register is not transferred into
the FIFO, therefore the data in the FIFO is not corrupted by the error.
LSR[2]: Receive Data Parity Error Tag
Logic 0 = No parity error (default).
Logic 1 = Parity error. The receive character in RHR does not have correct parity information and is suspect.
This error is associated with the character available for reading in RHR.
LSR[3]: Receive Data Framing Error Tag
Logic 0 = No framing error (default).
Logic 1 = Framing error. The receive character did not have a valid stop bit(s). This error is associated with
the character available for reading in RHR.
LSR[4]: Receive Break Tag
Logic 0 = No break condition (default).
Logic 1 = The receiver received a break signal (RX was LOW for at least one character frame time). In the
FIFO mode, only one break character is loaded into the FIFO. The break indication remains until the RX
input returns to the idle condition, “mark” or HIGH.
LSR[5]: Transmit Holding Register Empty Flag
This bit is the Transmit Holding Register Empty indicator. The THR bit is set to a logic 1 when the last data byte
is transferred from the transmit holding register to the transmit shift register. The bit is reset to logic 0
concurrently with the data loading to the transmit holding register by the host. In the FIFO mode this bit is set
when the transmit FIFO is empty, it is cleared when the transmit FIFO contains at least 1 byte.
LSR[6]: THR and TSR Empty Flag
This bit is set to a logic 1 whenever the transmitter goes idle. It is set to logic 0 whenever either the THR or
TSR contains a data character. In the FIFO mode this bit is set to a logic 1 whenever the transmit FIFO and
transmit shift register are both empty.
LSR[7]: Receive FIFO Data Error Flag
Logic 0 = No FIFO error (default).
Logic 1 = A global indicator for the sum of all error bits in the RX FIFO. At least one parity error, framing error
or break indication is in the FIFO data. This bit clears when there is no more error(s) in any of the bytes in the
RX FIFO.
相關PDF資料
PDF描述
XR16M564IV-0A-EVB EVAL BOARD FOR XR16M564-A 64LQFP
VI-J2H-EZ-S CONVERTER MOD DC/DC 52V 25W
2-5504971-8 CA 62.5/125 LDDZP SCDUP SCDUP
EEC08DRAS-S734 CONN EDGECARD 16POS .100 R/A PCB
CB5000-000 HEAT SHRINK TUBING
相關代理商/技術參數
參數描述
XR16M654IV64 制造商:EXAR 制造商全稱:EXAR 功能描述:1.62V TO 3.63V QUAD UART WITH 64-BYTE FIFO
XR16M654IV64-F 功能描述:UART 接口集成電路 1.62V-3.63V QUAD UART W/64BYTE FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16M654IV64TR-F 制造商:Exar Corporation 功能描述:UART 4-CH 64Byte FIFO 1.8V/2.5V/3.3V 64-Pin LQFP T/R
XR16M654IV80 制造商:EXAR 制造商全稱:EXAR 功能描述:1.62V TO 3.63V QUAD UART WITH 64-BYTE FIFO
XR16M654IV80-0A-EB 功能描述:界面開發工具 Eval Board for XR16M654IV80-0A RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*