- 您現在的位置：買賣IC網 > PDF目錄3766 > XR16M781IL24-F (Exar Corporation)IC UART FIFO 64B 24QFN PDF資料下載
參數資料
| 型號： | XR16M781IL24-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 32/52頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART FIFO 64B 24QFN |
| 標準包裝： | 490 |
| 特點： | * |
| 通道數： | 1，UART |
| FIFO's： | 64 字節 |
| 規程： | RS232，RS422，RS485 |
| 電源電壓： | 1.62 V ~ 3.63 V |
| 帶自動流量控制功能： | 是 |
| 帶IrDA 編碼器/解碼器： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-VFQFN 裸露焊盤 |
| 供應商設備封裝： | 24-QFN 裸露焊盤（4x4） |
| 包裝： | 托盤 |
| 其它名稱： | 1016-1463 XR16M781IL24-F-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
XR16M781
38
1.62V TO 3.63V UART WITH 64-BYTE FIFO AND VLIO INTERFACE
REV. 1.0.1
DLD[5:4]: Sampling Rate Select
These bits select the data sampling rate. By default, the data sampling rate is 16X. The maximum data rate will
double if the 8X mode is selected and will quadruple if the 4X mode is selected. See Table 14 below.
TABLE 14: SAMPLING RATE SELECT
SAMPLING RATE
0
16X
0
1
8X
1
X
4X
DLD[6]: Independent BRG enable
Logic 0 = The Transmitter and Receiver uses the same Baud Rate Generator. (default).
Logic 1 = The Transmitter and Receiver uses different Baud Rate Generators. Use DLD[7] for selecting
which baud rate generator to configure.
DLD[7]: BRG select
When DLD[6] = 1, this bit selects whether the values written to DLL, DLM and DLD[5:0] will be for the Transmit
Baud Rate Generator or the Receive Baud Rate Generator. When DLD[6] = 0 (same Baud Rate Generator
used for both TX and RX), this bit must be a logic 0 to properly write to the appropriate DLL, DLM and
DLD[5:0]. .
TABLE 15: BRG SELECT
0
Transmitter and Receiver uses same BRG.
Writing to DLL, DLM and DLD[5:0] configures the BRG for both the TX and RX.
0
1
Transmitter and Receiver uses different BRGs.
Writing to DLL, DLM and DLD[5:0] configures the BRG for TX.
1
Transmitter and Receiver uses different BRGs.
Writing to DLL, DLM and DLD[5:0] configures the BRG for RX.
1
0
Transmitter and Receiver uses same BRG.
Writing to DLL, DLM and DLD[5:0] has no effect on BRG used by the TX and RX.
4.14
Trigger Level Register (TRG) - Write-Only
User Programmable Transmit/Receive Trigger Level Register.
TRG[7:0]: Trigger Level Register
These bits are used to program desired trigger levels when trigger Table-D is selected. FCTR bit-7 selects
between programming the RX Trigger Level (a logic 0) and the TX Trigger Level (a logic 1).
4.15
RX/TX FIFO Level Count Register (FC) - Read-Only
This register replaces SPR (during a read) and is accessible when FCTR[6] = 1. This register is also
accessible when LCR = 0xBF. It is suggested to read the FIFO Level Count Register at the Scratchpad
Register location when FCTR bit-6 = 1. See Table 12.
DLD[5]
DLD[4]
DLD[7]
DLD[6]
BRG
相關PDF資料 |
PDF描述 |
|---|---|
| XR16M781IB25-F | IC UART FIFO 64B 25BGA |
| MAX7312AAG+T | IC I/O EXPANDER I2C 16B 24SSOP |
| XR16M890IL40-F | IC UART I2C/SPI 128 BYTE 40QFN |
| XR20M1280IL32-F | IC UART I2C/SPI 128 BYTE 32QFN |
| MAX7326ATG+T | IC I/O EXPANDER I2C 16B 24TQFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16M781IL32 | 制造商:EXAR 制造商全稱:EXAR 功能描述:1.62V TO 3.63V UART WITH 64-BYTE FIFO AND VLIO INTERFACE |
| XR16M781IL32-0C-EB | 功能描述:界面開發工具 Eval Board for XR16M781IL32 Series RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XR16M781IL32-F | 功能描述:UART 接口集成電路 1.62-3.63V; 64-Byte FIFO & VLIO; UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16M890 | 制造商:EXAR 制造商全稱:EXAR 功能描述:Single-Channel UARTs with Selectable Bus Interfaces |
| XR16M890_11 | 制造商:EXAR 制造商全稱:EXAR 功能描述:UART WITH 128-BYTE FIFO AND INTEGRATED LEVEL SHIFTERS |
發布緊急采購，3分鐘左右您將得到回復。