REV. 1.0.3 2.10 Receiver The receiver section contains an 8-bit Receiv" />
參數資料
型號： XR16V554IV-F
廠商： Exar Corporation
文件頁數： 8/43頁
文件大?。?/td> 0K
描述： IC UART FIFO 16B QUAD 64LQFP
標準包裝： 160
特點： *
通道數： 4，QUART
FIFO's： 16 字節
規程： RS232
電源電壓： 2.25 V ~ 3.6 V
帶自動流量控制功能： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 64-LQFP
供應商設備封裝： 64-LQFP（10x10）
包裝： 托盤
XR16V554/554D
16
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
REV. 1.0.3
2.10
Receiver
The receiver section contains an 8-bit Receive Shift Register (RSR) and 16 bytes of FIFO which includes a
byte-wide Receive Holding Register (RHR). The RSR uses the 16X clock for timing. It verifies and validates
every bit on the incoming character in the middle of each data bit. On the falling edge of a start or false start bit,
an internal receiver counter starts counting at the 16X clock rate. After 8 clocks the start bit period should be at
the center of the start bit. At this time the start bit is sampled and if it is still LOW it is validated. Evaluating the
start bit in this manner prevents the receiver from assembling a false character. The rest of the data bits and
stop bits are sampled and validated in this same manner to prevent false framing. If there were any error(s),
they are reported in the LSR register bits 2-4. Upon unloading the receive data byte from RHR, the receive
FIFO pointer is bumped and the error tags are immediately updated to reflect the status of the data byte in
RHR register. RHR can generate a receive data ready interrupt upon receiving a character or delay until it
reaches the FIFO trigger level. Furthermore, data delivery to the host is guaranteed by a receive data ready
time-out interrupt when data is not received for 4 word lengths as defined by LCR[1:0] plus 12 bits time. This is
equivalent to 3.7-4.6 character times. The RHR interrupt is enabled by IER bit-0. See Figure 9 and Figure 10
below.
2.10.1
Receive Holding Register (RHR) - Read-Only
The Receive Holding Register is an 8-bit register that holds a receive data byte from the Receive Shift
Register. It provides the receive data interface to the host processor. The RHR register is part of the receive
FIFO of 16 bytes by 11-bit wide, the 3 extra bits are for the 3 error tags to be reported in LSR register. When
the FIFO is enabled by FCR bit-0, the RHR contains the first data character received by the FIFO. After the
RHR is read, the next character byte is loaded into the RHR and the errors associated with the current data
byte are immediately updated in the LSR bits 2-4.
FIGURE 9. RECEIVER OPERATION IN NON-FIFO MODE
Receive Data Shift
Register (RSR)
Receive
Data Byte
and Errors
RHR Interrupt (ISR bit-2)
Receive Data
Holding Register
(RHR)
RXFIFO1
16X Clock
Receive Data Characters
Data Bit
Validation
Error
Tags in
LSR bits
4:2
相關PDF資料
PDF描述
VE-B5L-IW-F1 CONVERTER MOD DC/DC 28V 100W
VE-B5L-IX-F4 CONVERTER MOD DC/DC 28V 75W
VE-B5L-IX-F2 CONVERTER MOD DC/DC 28V 75W
MS27473E16B8P CONN PLUG 8POS STRAIGHT W/PINS
VE-B5L-IX-F1 CONVERTER MOD DC/DC 28V 75W
相關代理商/技術參數
參數描述
XR16V554IVTR-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16V564 制造商:EXAR 制造商全稱:EXAR 功能描述:2.25V TO 3.6V QUAD UART WITH 32-BYTE FIFO
XR16V564_07 制造商:EXAR 制造商全稱:EXAR 功能描述:2.25V TO 3.6V QUAD UART WITH 32-BYTE FIFO
XR16V564D 制造商:EXAR 制造商全稱:EXAR 功能描述:2.25V TO 3.6V QUAD UART WITH 32-BYTE FIFO
XR16V564DIV 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*