- 您現在的位置：買賣IC網 > PDF目錄16514 > XR17V252IM-0A-EVB (Exar Corporation)EVAL BOARD FOR XR17V252 100TQFP PDF資料下載
參數資料
| 型號： | XR17V252IM-0A-EVB |
| 廠商： | Exar Corporation |
| 文件頁數： | 11/69頁 |
| 文件大小： | 0K |
| 描述： | EVAL BOARD FOR XR17V252 100TQFP |
| 標準包裝： | 1 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁
XR17V252
19
REV. 1.0.2
66 MHZ PCI BUS DUAL UART WITH POWER MANAGEMENT SUPPORT
Timer Operation in Re-triggerable Mode:
In the re-triggerable mode, when the Timer is started, the Timer output will stay HIGH until it reaches half of the
terminal count N (= P clocks) and toggle LOW and stay LOW for a similar amount of time (Q clocks). The
above step will keep repeating until the Timer is stopped at which time the output will become HIGH (default
state). See Figure 7. Also, after the Timer is started, re-starting the Timer does not have any effect in re-
triggerable mode. The Timer must be programmed while it is stopped since the following operations are
blocked when the Timer is running:
■ Any write to TIMER MSB, LSB registers
■ Issue of any command other than ’Stop Timer’ and ’Reset Timer’ (’Start Timer’ is not allowed)
Routing the Timer Output to MPIO[0] Pin:
MPIO[0] pin is by default (on power up or reset, for example) an input. However, whenever the Timer output is
routed to MPIO[0] pin,
■ MPIO[0] will be automatically selected as an output
■ MPIO[0] will become HIGH (the default state of Timer output)
■ All MPIO control registers (MPIOLVL, MPIOSEL etc) lose control over MPIO[0] and get the control back
only when the Timer output is de-routed from MPIO[0].
Timer Interrupt
In the one-shot mode, the Timer will issue an interrupt upon timing out which is ’N’ clocks after the Timer is
started. In the re-triggerable mode, the Timer will keep issuing an interrupt every ’N’ clocks which is on every
rising edge of the Timer output. The Timer interrupt can be cleared by reading the TIMERCNTL register or
when a Timer Reset command is issued which brings the Timer back to its default settings. The TIMERCNTL
will read a value of 0x01 when the Timer interrupt is enabled and there is a pending interrupt. It reads a value
of 0x00 at all other times. Stopping the Timer does not clear the interrupt and neither does subsequent re-
starting.
FIGURE 7. TIMER OUTPUT IN ONE-SHOT AND RE-TRIGGERABLE MODES
TIMER Output in
Re-triggerable
Mode
TIMER Output in
One-Shot Mode
After 'P'
clocks
START TIMER
COMMAND ISSUED
START TIMER
COMMAND ISSUED
'N' Clocks
STOP TIMER
COMMAND ISSUED
START TIMER COMMANDS ISSUED: LESS THAN 'N'
CLOCKS BETWEEN SUCCESSIVE COMMANDS
< 'N' Clocks
After 'P'
clocks
After 'P'
clocks
After 'P'
clocks
After 'P'
clocks
After 'Q'
clocks
After 'Q'
clocks
After 'Q'
clocks
After 'Q'
clocks
< 'N' Clocks
相關PDF資料 |
PDF描述 |
|---|---|
| 6278890-4 | C/A 62.5 OFNR MTRJ-MTRJ RED SEC |
| 6374656-4 | C/A LC TO LC MM 2.0MM 4M |
| VE-J5R-EX | CONVERTER MOD DC/DC 7.5V 75W |
| RBC26DRXN | CONN EDGECARD 52POS DIP .100 SLD |
| RBM15DTMN | CONN EDGECARD 30POS R/A .156 SLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR17V252IM-F | 功能描述:UART 接口集成電路 66MHz Dual PCI UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR17V252IMTR-F | 制造商:Exar Corporation 功能描述:UART 2-CH 64Byte FIFO 3.3V 100-Pin TQFP T/R 制造商:Exar Corporation 功能描述:XR17V252IMTR-F |
| XR17V254 | 制造商:EXAR 制造商全稱:EXAR 功能描述:66MHZ PCI BUS QUAD UART WITH POWER MANAGEMENT SUPPORT |
| XR17V254_08 | 制造商:EXAR 制造商全稱:EXAR 功能描述:66MHZ PCI BUS QUAD UART WITH POWER MANAGEMENT SUPPORT |
| XR17V254IV | 制造商:EXAR 制造商全稱:EXAR 功能描述:66MHZ PCI BUS QUAD UART WITH POWER MANAGEMENT SUPPORT |
發布緊急采購，3分鐘左右您將得到回復。