參數資料
型號： XR88C92IV-F
廠商： Exar Corporation
文件頁數： 8/32頁
文件大?。?/td> 0K
描述： IC UART FIFO DUAL 44LQFP
標準包裝： 160
特點： *
通道數： 2，DUART
FIFO's： 16 字節
電源電壓： 2.97 V ~ 5.5 V
帶自動流量控制功能： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 44-LQFP
供應商設備封裝： 44-LQFP（10x10）
包裝： 托盤
XR88C92/192
16
Rev. 1.33
MODE REGISTER 0 (MR0A, MR0B)
This register is accessed only when command is applied
via CRA, CRB register (upper nibble = 0xB). After
reading or writing to MR0A (or MR0B) register, the mode
register pointer will point to MR1A (or MR1B) register.
MR0A Bit-0:
Extended baud rate table selection for both channels.
0 = Normal baud rate tables
1 = Extended baud rate tables 1
MR0A Bit-1: Special Function.
0 = Normal
1 = Factory test mode
MR0A Bit-2:
Extended baud rate table selection for both channels.
0 = Normal baud rate tables
1 = Extend baud rate tables 2
MR0A Bit-3, MR0B Bits 3-0:
Not Used. Any write to this bit is ignored.
MR0A, MR0B Bits 5-4:
Transmit trigger level select.
Bit-5
Bit-4
XR88C92
0
8 FIFO locations empty (default)
0
1
4 FIFO locations empty
1
0
6 FIFO locations empty
1
1 FIFO location empty
Bit-5
Bit-4
XR88C192
0
16 FIFO locations empty (default)
0
1
6 FIFO locations empty
1
0
12 FIFO locations empty
1
1 FIFO location empty
MR0A, MR0B Bit-6:
Receive trigger level select. This bit is associated with
MR1 Bit-6.
MR0 Bit-6
MR1 Bit-6
XR88C92
0
1 byte in FIFO (default)
0
1
3 bytes in FIFO
1
0
6 bytes in FIFO
1
8 bytes in FIFO
MR0 Bit-6
MR1 Bit-6
XR88C192
0
1 byte in FIFO (default)
0
1
6 bytes in FIFO
1
0
12 bytes in FIFO
1
16 bytes in FIFO
MR0A, MR0B Bit-7:
Receive time-out (watch dog timer).
0 = Disabled (default)
1 = Enabled
See description under 'Watchdog Timer'.
MODE REGISTER 1 (MR1A, MR1B)
MR1A, MR1B are accessed after reset or by command
applied via CRA, CRB register (upper nibble = 0x1).
After reading or writing to MR1A (or MR1B) register, the
mode register pointer will point to MR2A (or MR2B)
register.
MR1A, MR1B Bits 1-0:
Character Length
0 0 = 5 (default)
1 0 = 7
0 1 = 6
1 1 = 8
MR1A, MR1B Bit-2:
In non-Multidrop mode, this bit selects the parity.
0 = Even Parity (default)
1 = Odd Parity
In Multidrop mode, this bit is the Address/Data flag.
0 = Data (default)
1 = Address
MR1A, MR1B Bit 4-3: Parity mode.
00 = With parity (default)
10 = No parity
01 = Force parity
11 = Multidrop mode
MR1A, MR1B Bit-5: Data error mode.
0 = Single Character mode (default)
1 = Block (FIFO) mode
MR1A, MR1B Bit-6.
Receive trigger levels. See description under MR0 bit-
6.
MR1A, MR1B Bit-7: Receive RTS flow control.
0 = No RX RTS control function (default)
1 = Auto RX RTS control function
The output OP0 (OP1) serves as the -RTS signal for
channel A (channel B). Note that MR2 A/B bit-5 also
controls OP0 (OP1). Only one of MR1 bit-7 or MR2 bit-
5 should be set to '1'.
MODE REGISTER 2 (MR2A, MR2B)
This register is accessed
after any read or write
operation to MR1A (or MR1B) register is performed.
Any read or write to MR2A (or MR2B) does not change
the mode register pointer. User should use one of the
two reset MR pointer command (see Command
相關PDF資料
PDF描述
ST16C454CJ68TR-F IC UART QUAD 68PLCC
XR16C850CMTR-F IC UART FIFO 128B 48TQFP
XR16L570IL32-F IC UART FIFO 16B 32QFN
XR16L651CM-F IC UART FIFO 32B 48TQFP
XR68C92IJTR-F DUAL CHANNEL UART 44PLCC
相關代理商/技術參數
參數描述
XR9040 制造商:CK 功能描述:ELECTRICIANS PEN KNIFE
XR9101 制造商:3M Electronic Products Division 功能描述:EPOXY MASTIC XR9101
XR9102 制造商:3M Electronic Products Division 功能描述:EPOXY MASTIC XR9102
XR9103 制造商:3M Electronic Products Division 功能描述:EPOXY MASTIC XR9103
XR997 制造商:Intel 功能描述:INTEL 10GBASE-T
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*