參數資料
型號： XRT71D00IQTR-F
廠商： Exar Corporation
文件頁數： 6/26頁
文件大?。?/td> 0K
描述： IC JITTER ATTENUATOR SGL 32TQFP
標準包裝： 1,500
類型： *
PLL： 是
輸入： 時鐘
輸出： 時鐘
電路數： 1
比率 - 輸入:輸出： 3:2
差分 - 輸入:輸出： 無/無
頻率 - 最大： 44.736MHz
除法器/乘法器： 無/無
電源電壓： 3.135 V ~ 5.25 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 32-LQFP
供應商設備封裝： 32-TQFP（7x7）
包裝： 帶卷 (TR)
XRT71D00
á
E3/DS3/STS-1 JITTER ATTENUATOR
REV. 1.2.0
13
The XRT71D00 DS3/E3/STS-1 Jitter Attenuator IC
consists of the following functional blocks:
Jitter Attenuator Phase Locked Loop(PLL)
Timing Control
2-Channel 16/32 Bit FIFO.
Microprocessor Serial Interface
1.0
THE JITTER ATTENUATOR PLL
The Jitter Attenuator PLL is a narrow-band PLL that
accepts a “jittery” clock signal via the RCLK input pin.
The Jitter Attenuator PLL locks onto the RCLK input
signal and synthesizes a “same-rate” signal. As the
Jitter Attenuator PLL synthesizes this signal, it elimi-
nates much of the jitter that exists within the RCLK in-
put signal. The resulting smoothed clock signal is
then output via the “RRCLK” output signal.
1.1
THE JITTER TRANSFER CHARACTERISTICS OF THE
JITTER ATTENUATOR PLL
The Jitter Transfer Characteristics of the XRT71D00
device is ultimately dictated by the Jitter Transfer
Characteristics of the Jitter Attenuator PLL. The Jitter
Transfer Characteristics of the Jitter Attenuator PLL is
dictated by the following variables.
1. The operating mode/data rate of the XRT71D00
device.
2. The setting of the BWS (Bandwidth Select) input
pin or bit-field.
1.2
DEFINITION OF JITTER
One of the most important and least understood mea-
sures of clock performance is jitter. The International
Telecommunication Union defines jitter as “short term
variations of the significant instants of a digita signal
from their ideal positions in time”. Jitter can occur due
to any of the following:
1) Imperfect timing recovery circuit in the system
2) Cross-talk noise
3) Inter-symbol interference/Signal Distortion
1.3
JITTER TRANSFER CHARACTERISTICS
The primary purpose of jitter transfer requirements is
to prevent performance degradations by limiting the
accummulation of jitter through the system such that
it does not exceed the network interface jitter require-
ments. Thus, it is more important that a system meet
the jitter transfer criteria for relatively high input jitter
amplitudes. The jitter transferred through the system
must be under the jitter mask for any input jitter ampli-
tude within the range as shown in Figure 7
FIGURE 6. ILLUSTRATION OF THE XRT71D00 (CONFIGURED TO OPERATE IN THE “HOST” MODE)
HOST/HW
Reset
16/32 Bit FIFO
Microprocessor Serial
Interface
Timing Control Block /
Phase locked Loop
Write Clock
Read Clock
RRClk
RRPOS
RRNEG
FL
RClk
RPOS
RNEG
ICT
CS
SDI
SDO
SClk
MClk
Smoothed
Clock
Jittery Clock
相關PDF資料
PDF描述
X9421WV14I-2.7T1 IC XDCP SGL 64-TAP 10K 14-TSSOP
X9421WV14-2.7T1 IC XDCP SGL 64-TAP 10K 14-TSSOP
SY89536LHZ IC SYNTHESIZR LVPECL/HSTL 64TQFP
VI-253-MW-S CONVERTER MOD DC/DC 24V 100W
V28A5H175B CONVERTER MOD DC/DC 5V 175W
相關代理商/技術參數
參數描述
XRT71D03 制造商:EXAR 制造商全稱:EXAR 功能描述:3 CHANNEL E3/DS3/STS-1 JITTER ATTENUATOR
XRT71D03ES 功能描述:時鐘合成器/抖動清除器 3CH T3/E3JA w/T73LC03A RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT71D03IV 制造商:EXAR 制造商全稱:EXAR 功能描述:3 CHANNEL E3/DS3/STS-1 JITTER ATTENUATOR
XRT71D03IV-F 功能描述:時鐘合成器/抖動清除器 RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT71D03IVTR-F 功能描述:時鐘合成器/抖動清除器 RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*