- 您現在的位置：買賣IC網 > PDF目錄376460 > XRT71D03 (EXAR CORP) 3-Channel E3/DS3/STS-1 Jitter Attenuator,STS-1 to DS3 Desynchronizer(達到E3/DS3/STS-1振蕩要求的3通道振蕩衰減器) PDF資料下載
參數資料
| 型號： | XRT71D03 |
| 廠商： | EXAR CORP |
| 元件分類： | 數字傳輸電路 |
| 英文描述： | 3-Channel E3/DS3/STS-1 Jitter Attenuator,STS-1 to DS3 Desynchronizer(達到E3/DS3/STS-1振蕩要求的3通道振蕩衰減器) |
| 中文描述： | DATACOM, PCM JITTER ATTENUATOR, PQFP64 |
| 封裝： | 10 X 10 MM, 1.40 MM HEIGHT, LQFP-64 |
| 文件頁數： | 14/20頁 |
| 文件大?。?/td> | 210K |
| 代理商： | XRT71D03 |
XRT71D03
3 CHANNEL E3/DS3/STS-1 JITTER ATTENUATOR, STS-1 TO DS3 DESYNCHRONIZER
REV. P1.0.2
á
PRELIMINARY
14
The serial interface for the XRT71D03 and the
XRT7300 family of E3/DS3/STS-1 LIU’s, which
makes it easy to configure both the XRT71D03 and
the LIU with a single CS, SDI, SDO and SClk input
and output pins.
S
ERIAL
I
NTERFACE
O
PERATION
.
Serial interface data structure and timings are provid-
ed in Figure 5 and 6 respectively.
The clock signal is provided to the SClk and the CS is
asserted for 50 ns prior to the first rising edge of the
SClk.
B
IT
1—R/W (R
EAD
/W
RITE
) B
IT
This bit will be clocked into the SDI input, on the first
rising edge of SClk (after CS has been asserted).
This bit indicates whether the current operation is a
Read or Write operation. A “1” in this bit specifies a
Read operation; whereas, a “0” in this bit specifies a
Write operation.
Bits 2 through 5: The five (5) bit Address Values (la-
beled A0, A1, A2 ,A3,and A4)
The next four rising edges of the SClk signal will clock
in the 5-bit address value for this particular Read (or
Write) operation. The address selects the Command
Register for reading data from, or writing data to. The
address bits to the SDI input pin is applied in ascend-
ing order with the LSB (least significant bit) first.
B
IT
7:
A5 must be set to “0”, as shown in Figure 7.
B
IT
8—A6
The value of A6 is a don’t care.
Once these first 8 bits have been written into the Seri-
al Interface, the subsequent action depends upon
whether the current operation is a Read or Write op-
eration.
R
EAD
O
PERATION
Once the last address bit (A4) has been clocked into
the SDI input, the Read operation will proceed
through an idle period, lasting three SClk periods. On
the falling edge of SClk Cycle #8 (see Figure 7) the
serial data output signal (SDO) becomes active. At
this point the user can begin reading the data con-
tents of the addressed Command Register (at Ad-
dress [A4,A3, A2, A1, A0]) via the SDO output pin.
The Serial Interface will output this seven bit data
word (D0 through D6) in ascending order (with the
LSB first), on the falling edges of the SClk . The data
(on the SDO output pin) is stable for reading on the
very next rising edge of the SClk .
W
RITE
O
PERATION
Once the last address bit (A4) has been clocked into
the SDI input, the Write operation will proceed
through an idle period, lasting three SClk periods. Pri-
or to the rising edge of SClk Cycle #9 , eight bit data
word is applied to SDI input. Data on SDI is latched
on the rising edge of SClk.
T
ABLE
2: A
DDRESS
AND
B
IT
F
ORMATS
OF
THE
C
OMMAND
R
EGISTERS
A
DDR
C
OMMAND
R
EGISTER
T
YPE
D6
D5
D4
D3
D2
D1
D0
0X06
CR6
R/W
***
***
DS3/E3_ch0
DJA0
STS-1_ch0
ClkES0
FSS0
0x07
CR7
RO
***
***
***
***
***
***
FL0
0x0E
CR14
R/W
***
***
DS3/E3_ch1
DJA1
STS-1_ch1
ClkES1
FSS1
0x0F
CR15
RO
***
***
***
***
***
***
FL1
0x16
CR22
R/W
***
***
DS3/E3_ch2
DJA2
STS-1_ch2
ClkES2
FSS2
0x17
CR23
RO
***
***
***
***
***
***
FL2
相關PDF資料 |
PDF描述 |
|---|---|
| XRT71D04 | 4-Channel E3/DS3/STS-1 Jitter Attenuator,STS-1 to DS3 Desynchronizer(達到E3/DS3/STS-1振蕩要求的4通道振蕩衰減器) |
| XRT7234 | E3 ATM User Network Interface(E3異步傳輸模式用戶網絡接口) |
| XRT7245 | DS3 ATM User Network Interface(DS3異步傳輸模式用戶網絡接口) |
| XRT7288IP | CEPT1 Line Interface |
| XRT7288 | CEPT1 Line Interface(CEPT1線接口) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT71D03ES | 功能描述:時鐘合成器/抖動清除器 3CH T3/E3JA w/T73LC03A RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
| XRT71D03IV | 制造商:EXAR 制造商全稱:EXAR 功能描述:3 CHANNEL E3/DS3/STS-1 JITTER ATTENUATOR |
| XRT71D03IV-F | 功能描述:時鐘合成器/抖動清除器 RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
| XRT71D03IVTR-F | 功能描述:時鐘合成器/抖動清除器 RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
| XRT71D04 | 制造商:EXAR 制造商全稱:EXAR 功能描述:4 CHANNEL E3/DS3/STS-1 JITTER ATTENUATOR, STS-1 TO DS3 DESYNCHRONIZER |
發布緊急采購，3分鐘左右您將得到回復。