參數資料
型號： XTR108
英文描述： 4-20mA, TWO-WIRE TRANSMITTER Smart Programmable with Signal Conditioning
中文描述： 的4 - 20mA，兩線制變送器可編程智能與信號調理
文件頁數： 15/27頁
文件大?。?/td> 497K
代理商： XTR108
XTR108
SBOS187B
15
www.ti.com
Address = 11: Coarse I
REF
Adjust Register
This register sets the code to the 8-bit coarse DAC that adjusts
the magnitude of both reference currents. The nominal value
for the reference current (both Coarse and Fine adjust set to ‘0’)
is I
PROGRAM
5. See Table III for formulas.
Address = 12: Fine Zero-Adjust Register
This register sets the code to the 8-bit Fine DAC that adjusts
the magnitude of the zero output currents. Equations are
given in Table II. Negative numbers are in Binary Two’s
Complement.
Address = 13: Coarse Zero-Adjust Register
This register sets the code to the 8-bit Coarse DAC that
adjusts the magnitude of zero-output current. See Table II
for equations. Negative numbers are given in Binary Two’s
Complement.
Address = 14: Linearization Adjust Register
This register sets the code to the 8-bit DAC that adjusts the
magnitude of the linearization feedback current. Value is
unipolar to 255.
Address = 15: Checksum Register
This register contains the checksum byte that is used to
validate the data read from the EEPROM. If a write occurs
to this register, and the checksum is invalid, an error condi-
tion will set (CSE = ‘1’). If the checksum is valid, the error
condition will be cleared (CSE = ‘0’).
If a checksum error is detected, the XTR108 will program
itself to the lowest under-scale error level.
SERIAL INTERFACE
PROTOCOL
The XTR108 has an SPI-compatible serial interface. The
data is transmitted MSB first in 8-bit bytes. The first byte is
an instruction byte in which the first bit is a read/write flag
(‘0’ = write, ‘1’ = read), the lowest four bits are the register
address and the remaining three bits are set to zero. The
second, and all successive bytes, are data. During a write
operation, the successive data bytes are written to successive
registers within the XTR108. The address is automatically
incremented at the completion of each byte. The SDIO line
is always an input during a write operation. During a read
operation, the SDIO line becomes an output during the
second and successive bytes. As in the case of a write
operation, the address is automatically incremented at the
completion of each byte. Each communication transaction is
terminated when CS1 is de-asserted. The CS2 line remains
de-asserted during read and write operations.
The calibration controller also needs to be able to read from
and write to the external EEPROM device. This is accom-
plished by sending a special instruction code (0x7F) to the
XTR108. At the completion of this instruction byte, the
XTR108 will assert the CS2 line to select the EEPROM
device and ignore all data on the SDIO line until CS1 is de-
asserted and reasserted. The CS2 line will also be de-
asserted when CS1 is de-asserted. This allows the calibra-
tion controller to communicate with the EEPROM device
directly. The calibration controller then has control over the
timing required to write data to the EEPROM device.
In normal operation, the XTR108 reads data from the EEPROM
device to retrieve calibration coefficients. This is accom-
plished by the read-back controller on the XTR108. The read-
back controller is clocked by an on-chip oscillator and pro-
vides stimulus to the EEPROM device over the SCLK, SDIO,
and CS2 lines to perform the read operation, while simulta-
neously providing stimulus to the serial interface controller in
the XTR108. The read-back controller defaults to being active
when the XTR108 is powered on and will be continuously
active unless disabled. (It will start a new read operation as
soon as the previous operation is completed, see Figure 4.) A
control bit (RBD) is provided to allow the XTR108 to read the
EEPROM once and then stop.
The read-back controller will abort a read-back operation
when the CS1 line is asserted. The calibration controller
must wait at least 40
μ
s after setting the CS1 line LOW
before the first rising edge of SCLK occurs.
For an external controller to write directly to the XTR108
(sensor calibration operation) or load data into the EEPROM,
it is necessary to interrupt the default read-back mode. For
both of these modes, the SCLK direction must be reversed.
See Figure 5 for the timing of this operation. First, the SCLK
line must be pulled LOW for at least 20ns (t
10
). Then CS1
is set LOW. The XTR108 will set DIO to a tri-state within
20ns (t
13
) and CS2 HIGH within 50ns (t
12
). After a delay of
at least 40
μ
s (t
11
), the external system will start communica-
tion with a rising edge on SCLK.
As long as CS1 is held LOW, the external system can write to
the EEPROM. See Figure 7 for this timing. Releasing CS1
will allow the XTR108 to resume in the read-back mode.
For interactive calibration operations, the first command to
the XTR108 should set bit 0, Register 4 (RBD). This will
disable the read-back mode. It will be possible to write to the
various registers and cycle CS1. If RBD is not set, then as
soon as CS1 is released, the XTR108 will read the EEPROM
contents which will overwrite the data just loaded. Figure 6
shows read and write timing.
IA2
IA1
IA0
I
REF
CONNECTION
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
I
REF
1 Connected to V/I-0
I
REF
1 Connected to V/I-1
I
REF
1 Connected to V/I-2
I
REF
1 Connected to V/ I-3
I
REF
1 Connected to V/ I-4
I
REF
1 Connected to V/I-5
Reserved
Reserved
IB2
IB1
IB0
I
REF
CONNECTION
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
I
REF
2 Connected to V/I-0
I
REF
2 Connected to V/I-1
I
REF
2 Connected to V/ I-2
I
REF
2 Connected to V/I-3
I
REF
2 Connected to V/I-4
I
REF
2 Connected to V/ I-5
Reserved
Reserved
TABLE XIII. Register 9, I
REF
Output Configuration.
相關PDF資料
PDF描述
XTR108EA 4-20mA, TWO-WIRE TRANSMITTER Smart Programmable with Signal Conditioning
XTR110L LCC Precision Voltage-to-Current Converter/Transmitter
XTR501 XTR501 - HIGH CURRENT BRIDGE DRIVER and 4-20mA Transmitter
XTTEK100Q56 PSU 100W 4 O/P U FRAME
XTTEK100Q86 PSU 100W 4 O/P U FRAME
相關代理商/技術參數
參數描述
XTR108_12 制造商:BB 制造商全稱:BB 功能描述:4-20mA, TWO-WIRE TRANSMITTER a??Smarta?? Programmable with Signal Conditioning
XTR108-DIE 制造商:TI 制造商全稱:Texas Instruments 功能描述:TWO-WIRE TRANSMITTER
XTR108EA 功能描述:接口 - 專用 4-20mA 2Wire Trsmtr ’Smart’ Prog RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
XTR108EA/2K5 功能描述:接口 - 專用 4-20mA 2Wire Trsmtr ’Smart’ Prog RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
XTR108EA/2K5G4 功能描述:接口 - 專用 4-20mA 2Wire Trsmtr ’Smart’ Prog RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*