- 您現在的位置：買賣IC網 > PDF目錄48103 > YNC12S20-DS1G (POWER-ONE INC) 1-OUTPUT DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | YNC12S20-DS1G |
| 廠商： | POWER-ONE INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 封裝： | ROHS COMPLIANT PACKAGE-5 |
| 文件頁數： | 24/28頁 |
| 文件大?。?/td> | 337K |
| 代理商： | YNC12S20-DS1G |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁
ZD-02137 Rev. 2.1 21-Jun-10
Page 5 of 28
www.power-one.com
YNC12S20 DC-DC Converter Data Sheet
9.6-14 VDC Input; 0.7525-5.5 VDC Programmable @ 20 A
Operation
Input and Output Impedance
The Y-Series converter should be connected via a
low impedance to the DC power source. In many
applications, the inductance associated with the
distribution from the power source to the input of
the converter can affect the stability of the
converter. It is recommended to use decoupling
capacitors in order to ensure stability of the
converter and reduce input ripple voltage. The
converter has an internal input capacitance of 40
μF with very low ESR (ceramic capacitors).
In a typical application, low - ESR tantalum or
POS capacitors will be sufficient to provide
adequate ripple voltage filtering at the input of the
converter. However, very low ESR ceramic
capacitors 47μF-100 μF are recommended at the
input of the converter in order to minimize the
input ripple voltage. They should be placed as
close as possible to the input pins of the converter.
YNC12S20
has
been
designed
for
stable
operation with or without external capacitance.
Low ESR ceramic capacitors placed as close as
possible to the load (Min 47 μF) are recommended
for improved transient performance and lower
output voltage ripple.
It is important to keep low resistance and low
inductance PCB traces for connecting load to the
output pins of the converter in order to maintain
good load regulation.
ON/OFF (Pin 1)
The ON/OFF pin is used to turn the power
converter on or off remotely via a system signal.
There are two remote control options available,
positive logic (standard option) and negative logic,
and both are referenced to GND. Typical
connections are shown in Fig. A.
The positive logic version turns the converter on
when the ON/OFF pin is at a logic high or left
open, and turns the converter off when at a logic
low or shorted to GND.
Vin
CONTROL
INPUT
Vin
GND
ON/OFF
SENSE
(Top View)
Converter
TRIM
Vout
R*
R* is for negative logic option only
Rload
Nex -c Series
TM
Fig. A: Circuit configuration for ON/OFF function.
The negative logic version turns the converter on
when the ON/OFF pin is at logic low or left open,
and turns the converter off when the ON/OFF pin
is at a logic high or connected to Vin.
ON/OFF pin is internally pulled-up to Vin for a
positive logic version, and pulled-down for a
negative logic version. A TTL or CMOS logic gate,
open collector (open drain) transistor can be used
to drive ON/OFF pin. When using open collector
(open drain) transistor with a negative logic option,
add a pull-up resistor (R*) of 75 k to Vin as
shown in Fig. A; This device must be capable of:
- sinking up to 0.2 mA at a low level voltage of
0.8 V
- sourcing up to 0.25 mA at a high logic level of
2.3V – 5V
- sourcing up to 0.75 mA when connected to Vin.
Remote Sense (Pin 2)
The remote sense feature of the converter
compensates for voltage drops occurring only
between Vout pin (Pin 4) of the converter and the
load. The SENSE (Pin 2) pin should be connected
at the load or at the point where regulation is
required (see Fig. B). There is no sense feature on
the output GND return pin, where a solid ground
plane is recommended to provide low voltage
drop.
If remote sensing is not required, the SENSE pin
must be connected to the Vout pin (Pin 4) to
ensure the converter will regulate at the specified
output voltage. If these connections are not made,
the converter will deliver an output voltage that is
slightly higher than the specified value.
相關PDF資料 |
PDF描述 |
|---|---|
| YNC12S20-0S1 | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| YNL05S10009-001 | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| YNL05S10015-D01 | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| YNL05S10033-D02G | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| YNL05S10033-002G | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| YNC13S20A-0 | 制造商:POWER-ONE 制造商全稱:Power-One 功能描述:9.6-14 VDC Input; 0.7525-5.5 VDC Programmable 20 A |
| YNC13S20A-0G | 制造商:POWER-ONE 制造商全稱:Power-One 功能描述:9.6-14 VDC Input; 0.7525-5.5 VDC Programmable 20 A |
| YNC13S20A-D | 制造商:POWER-ONE 制造商全稱:Power-One 功能描述:9.6-14 VDC Input; 0.7525-5.5 VDC Programmable 20 A |
| YNC13S20A-DG | 制造商:POWER-ONE 制造商全稱:Power-One 功能描述:9.6-14 VDC Input; 0.7525-5.5 VDC Programmable 20 A |
| YNC14S20A-0 | 制造商:POWER-ONE 制造商全稱:Power-One 功能描述:9.6-14 VDC Input; 0.7525-5.5 VDC Programmable 20 A |
發布緊急采購，3分鐘左右您將得到回復。