- 您現在的位置：買賣IC網 > PDF目錄48103 > YNC12S20-DS1G (POWER-ONE INC) 1-OUTPUT DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | YNC12S20-DS1G |
| 廠商： | POWER-ONE INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 封裝： | ROHS COMPLIANT PACKAGE-5 |
| 文件頁數： | 27/28頁 |
| 文件大?。?/td> | 337K |
| 代理商： | YNC12S20-DS1G |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁
ZD-02137 Rev. 2.1 21-Jun-10
Page 8 of 28
www.power-one.com
YNC12S20 DC-DC Converter Data Sheet
9.6-14 VDC Input; 0.7525-5.5 VDC Programmable @ 20 A
Characterization
General Information
The converter has been characterized for many
operational aspects, to include thermal derating
(maximum load current as a function of ambient
temperature and airflow) for vertical and horizontal
mounting, efficiency, start-up and shutdown
parameters, output ripple and noise, transient
response to load step-change, overload, and short
circuit.
The figures are numbered as Fig. x.y, where x
indicates the different output voltages, and y
associates with specific plots (y = 1 for the vertical
thermal derating, …). For example, Fig. x.1 will
refer to the vertical thermal derating for all the
output voltages in general.
The following pages contain specific plots or
waveforms
associated
with
the
converter.
Additional comments for specific data are provided
below.
Test Conditions
All thermal and efficiency data presented were
taken with the converter soldered to a test board,
specifically a 0.060” thick printed wiring board
(PWB) with four layers. The top and bottom layers
were not metalized. The two inner layers,
comprising two-ounce copper, were used to
provide traces for connectivity to the converter.
The lack of metalization on the outer layers as well
as the limited thermal connection ensured that
heat transfer from the converter to the PWB was
minimized. This provides a worst-case but
consistent scenario for thermal derating purposes.
All measurements requiring airflow were made in
vertical and horizontal wind tunnel facilities using
Infrared (IR) thermography and thermocouples for
thermometry.
Ensuring components on the converter do not
exceed their ratings is important to maintaining
high reliability. If one anticipates operating the
converter at or close to the maximum loads
specified in the derating curves, it is prudent to
check actual operating temperatures in the
application. Thermographic imaging is preferable;
if
this
capability
is
not
available,
then
thermocouples
may
be
used.
Power-One
recommends the use of AWG #40 gauge
thermocouples to ensure measurement accuracy.
Careful routing of the thermocouple leads will
further minimize measurement error. Refer to Fig.
E for optimum measuring thermocouple location.
Thermal Derating
Load current vs. ambient temperature and airflow
rates are given in Figs. x.1 for maximum
temperature of 120 °C. Ambient temperature was
varied between 25 °C and 85 °C, with airflow rates
from 30 to 500 LFM (0.15m/s to 2.5 m/s), and
vertical converter mounting. The airflow during the
testing is parallel to the short axis of the converter,
going from pin 1 and pin 6 to pins 2 – 5.
For each set of conditions, the maximum load
current was defined as the lowest of:
(i) The output current at which either any MOSFET
temperature did not exceed a maximum specified
temperature
(120°C)
as
indicated
by
the
thermographic image, or
(ii) The maximum current rating of the converter
(20 A)
During normal operation, derating curves with
maximum FET temperature less than or equal to
120 °C should not be exceeded. Temperature on
the PCB at the thermocouple location shown in
Fig. E should not exceed 120 °C in order to
operate inside the derating curves.
Fig. E: Location of the thermocouple for thermal testing.
Efficiency
Figure x.2 shows the efficiency vs. load current
plot for ambient temperature of 25 C, airflow rate
of 200 LFM (1 m/s) and input voltages of 9.6 V,
12 V, and 14 V.
相關PDF資料 |
PDF描述 |
|---|---|
| YNC12S20-0S1 | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| YNL05S10009-001 | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| YNL05S10015-D01 | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| YNL05S10033-D02G | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| YNL05S10033-002G | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| YNC13S20A-0 | 制造商:POWER-ONE 制造商全稱:Power-One 功能描述:9.6-14 VDC Input; 0.7525-5.5 VDC Programmable 20 A |
| YNC13S20A-0G | 制造商:POWER-ONE 制造商全稱:Power-One 功能描述:9.6-14 VDC Input; 0.7525-5.5 VDC Programmable 20 A |
| YNC13S20A-D | 制造商:POWER-ONE 制造商全稱:Power-One 功能描述:9.6-14 VDC Input; 0.7525-5.5 VDC Programmable 20 A |
| YNC13S20A-DG | 制造商:POWER-ONE 制造商全稱:Power-One 功能描述:9.6-14 VDC Input; 0.7525-5.5 VDC Programmable 20 A |
| YNC14S20A-0 | 制造商:POWER-ONE 制造商全稱:Power-One 功能描述:9.6-14 VDC Input; 0.7525-5.5 VDC Programmable 20 A |
發布緊急采購，3分鐘左右您將得到回復。