- 您現在的位置：買賣IC網 > PDF目錄48107 > YNV12T05 (POWER-ONE INC) DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | YNV12T05 |
| 廠商： | POWER-ONE INC |
| 元件分類： | 電源模塊 |
| 英文描述： | DC-DC REG PWR SUPPLY MODULE |
| 封裝： | ROHS COMPLIANT, SIP-5 |
| 文件頁數： | 24/26頁 |
| 文件大?。?/td> | 429K |
| 代理商： | YNV12T05 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁
Mar 25, 2005 revised to JUL 28, 2006
Page 7 of 26
www.power-one.com
YNV12T05 DC-DC Converter Data Sheet
9.6-14 VDC Input; 0.7525-5.5 VDC Programmable @ 5 A
The following pages contain specific plots or
waveforms associated with the converter. Additional
comments for specific data are provided below.
Test Conditions
All data presented were taken with the converter
soldered to a test board, specifically a 0.060” thick
printed wiring board (PWB) with four layers. The top
and bottom layers were not metalized. The two inner
layers, comprised of two-ounce copper, were used to
provide traces for connectivity to the converter.
The lack of metalization on the outer layers as well
as the limited thermal connection ensured that heat
transfer from the converter to the PWB was
minimized. This provides a worst-case but consistent
scenario for thermal derating purposes.
All measurements requiring airflow were made in the
vertical and horizontal wind tunnels using Infrared
(IR)
thermography
and
thermocouples
for
thermometry.
Ensuring components on the converter do not
exceed their ratings is important to maintaining high
reliability. If one anticipates operating the converter
at or close to the maximum loads specified in the
derating curves, it is prudent to check actual
operating
temperatures
in
the
application.
Thermographic
imaging
is
preferable;
if
this
capability is not available, then thermocouples may
be used. The use of AWG #40 gauge thermocouples
is recommended to ensure measurement accuracy.
Careful routing of the thermocouple leads will further
minimize measurement error. Refer to Fig. C for
optimum measuring thermocouple location.
Fig. C: Location of the thermocouple for thermal testing
.
Thermal Derating
Load current vs. ambient temperature and airflow
rates are given in Figs. x.1 to x.2 for maximum
temperature of 120 °C. Ambient temperature was
varied between 25 °C and 85 °C, with airflow rates
from 30 to 500 LFM (0.15 to 2.5 m/s), and vertical
and horizontal converter mounting. The airflow
during the testing is parallel to the long axis of the
converter, going from input pins to output pins.
For each set of conditions, the maximum load
current is defined as the lowest of:
(i) The output current at which any MOSFET
temperature
does
not
exceed
a
maximum
specified temperature (120 °C) as indicated by the
thermographic image, or
(ii) The maximum current rating of the converter (5A)
During normal operation, derating curves with
maximum FET temperature less than or equal to
120 °C should not be exceeded. Temperature on the
PCB at the thermocouple location shown in Fig. C
should not exceed 120 °C in order to operate inside
the derating curves.
Efficiency
Figure x.3 shows the efficiency vs. load current plot
for ambient temperature of 25 C, airflow rate of
200 LFM (1 m/s) and input voltages of 9.6 V, 12 V,
and 14 V.
Power Dissipation
Fig. x.4 shows the power dissipation vs. load current
plot for Ta = 25 C, airflow rate of 200 LFM (1 m/s)
with vertical mounting and input voltages of 9.6 V,
12 V, and 14 V.
Ripple and Noise
The output voltage ripple waveform is measured at
full rated load current. Note that all output voltage
waveforms are measured across a 1
μF ceramic
capacitor.
The output voltage ripple and input reflected ripple
current waveforms are obtained using the test setup
shown in Fig. D.
iS
Vout
Vsource
1
μF
ceramic
capacitor
DC/DC
Converter
4 x 47
μF
ceramic
capacitor
47
μF
ceramic
capacitor
CO
Vin
Y-Series
GND
Vout
GND
1
μH
source
inductance
CIN
Fig. D: Test Set-up for measuring input reflected ripple
currents,
is and output voltage ripple.
相關PDF資料 |
PDF描述 |
|---|---|
| YNV12T10-0 | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| YNV12T10-0G | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| YNV12T10-0-G | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| YNV12T10-D | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| YNV12T10-DG | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| YNV12T05G | 制造商:Power-One 功能描述:Module DC-DC 1-OUT 0.7525V to 5.5V 5A 27.5W 5-Pin SIP |
| YNV12T05-G | 功能描述:DC/DC轉換器 0.7525-5.5Vout 5A 9.6-14VIn RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| YNV12T05-G-Q | 制造商:Power-One 功能描述:DC/DC CONVERTER 0.7525-5.5V 28W |
| YNV12T10-0 | 功能描述:DC/DC轉換器 RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| YNV12T10010-0 | 制造商:Power-One 功能描述:DC/DC PS SGL-OUT 1V 10A 50W 10SIP - Bulk |
發布緊急采購，3分鐘左右您將得到回復。