- 您現在的位置：買賣IC網 > PDF目錄48107 > YNV12T05G (POWER-ONE INC) DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | YNV12T05G |
| 廠商： | POWER-ONE INC |
| 元件分類： | 電源模塊 |
| 英文描述： | DC-DC REG PWR SUPPLY MODULE |
| 封裝： | ROHS COMPLIANT, SIP-5 |
| 文件頁數： | 22/26頁 |
| 文件大小： | 429K |
| 代理商： | YNV12T05G |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁
Mar 25, 2005 revised to JUL 28, 2006
Page 5 of 26
www.power-one.com
YNV12T05 DC-DC Converter Data Sheet
9.6-14 VDC Input; 0.7525-5.5 VDC Programmable @ 5 A
Operations
Input and Output Impedance
The Y-Series converter should be connected via a
low impedance to the DC power source. In many
applications, the inductance associated with the
distribution from the power source to the input of the
converter can affect the stability of the converter. It is
recommended to use decoupling capacitors placed
as close as possible to the converter’s input pins in
order to ensure stability of the converter and reduce
input ripple voltage. Internally, the converter has
20 μF (low ESR ceramics) of input capacitance.
In a typical application, low - ESR tantalum or POS
capacitors will be sufficient to provide adequate
ripple voltage filtering at the input of the converter.
However,
very
low
ESR
ceramic
capacitors
47 to 100 μF are recommended at the input of the
converter in order to minimize the input ripple
voltage. They should be placed as close as possible
to the input pins of the converter.
The YNV12T05 has been designed for stable
operation with or without external capacitance. Low
ESR ceramic capacitors placed as close as possible
to the load (minimum 47 μF) are recommended for
better transient performance and lower output
voltage ripple.
It is important to keep low resistance and low
inductance PCB traces for connecting load to the
output pins of the converter in order to maintain good
load regulation.
ON/OFF (Pin 5)
The ON/OFF pin (Pin 5) is used to turn the converter
on or off remotely via a system signal that is
referenced to GND (Pin 3). Typical connections are
shown in Fig. A.
Vin
CONTROL
INPUT
Vin
GND
ON/OFF
(Top View)
Converter
TRIM
Vout
R*
Rload
Y-Series
Fig. A: Circuit configuration for ON/OFF function.
To turn the converter on the ON/OFF pin should be
at a logic low or left open, and to turn the converter
off the ON/OFF pin should be at a logic high or
connected to Vin.
The ON/OFF pin is internally pulled down. A TTL or
CMOS
logic
gate,
open-collector
(open-drain)
transistor can be used to drive ON/OFF pin. When
using open collector (open-drain) transistor, add a
pull-up resistor (R*) of 75 k
Ω to Vin as shown in
Fig. A. This device must be capable of:
- sinking up to 0.2 mA at a low level voltage of
≤ 0.8 V
- sourcing up to 0.25 mA at a high logic level of
2.3 to 5 V
- sourcing up to 0.75 mA when connected to Vin.
Output Voltage Programming (Pin 2)
The output voltage can be programmed from 0.7525
to 5.5 V by connecting an external resistor between
the TRIM pin (Pin 2) and the GND pin (Pin 3); see
Fig. B.
A trim resistor, RTRIM, for a desired output voltage
can be calculated using the following equation:
1
0.7525)
-
(V
5
.
10
R
REQ
-
O
RIM
T
=
[k
Ω]
where,
=
TRIM
R
Required value of trim resistor [k
Ω]
=
REQ
O
V
Desired (trimmed) output voltage [V]
Vin
RTRIM
Rload
Converter
Vin
GND
ON/OFF
(Top View)
TRIM
Vout
Y-Series
Fig. B: Configuration for programming output voltage.
Note that the tolerance of a trim resistor directly
affects
the
output
voltage
tolerance.
It
is
recommended to use standard 1% or 0.5% resistors;
for tighter tolerance, two resistors in parallel are
recommended rather than one standard value from
Table 1.
The ground pin of the trim resistor should be
connected directly to the converter’s GND pin (Pin 3)
with no voltage drop in between. Table 1 provides
the trim resistor values for popular output voltages.
相關PDF資料 |
PDF描述 |
|---|---|
| YNV12T05 | DC-DC REG PWR SUPPLY MODULE |
| YNV12T10-0 | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| YNV12T10-0G | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| YNV12T10-0-G | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| YNV12T10-D | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| YNV12T05-G | 功能描述:DC/DC轉換器 0.7525-5.5Vout 5A 9.6-14VIn RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| YNV12T05-G-Q | 制造商:Power-One 功能描述:DC/DC CONVERTER 0.7525-5.5V 28W |
| YNV12T10-0 | 功能描述:DC/DC轉換器 RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| YNV12T10010-0 | 制造商:Power-One 功能描述:DC/DC PS SGL-OUT 1V 10A 50W 10SIP - Bulk |
| YNV12T10010-0G | 制造商:Power-One 功能描述:DC/DC PS SGL-OUT 1V 10A 50W 10SIP - Bulk |
發布緊急采購，3分鐘左右您將得到回復。