- 您現在的位置：買賣IC網 > PDF目錄1887 > 101-0521 (Rabbit Semiconductor)MODULE RABBITCORE RCM3210 PDF資料下載
參數資料
| 型號： | 101-0521 |
| 廠商： | Rabbit Semiconductor |
| 文件頁數： | 46/138頁 |
| 文件大?。?/td> | 0K |
| 描述： | MODULE RABBITCORE RCM3210 |
| 標準包裝： | 1 |
| 系列： | RabbitCore® |
| 模塊/板類型： | MPU 核心模塊 |
| 適用于相關產品： | RCM3210 |
| 其它名稱： | 101-521 101-521-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁當前第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁
User’s Manual
9
2. HARDWARE SETUP
This chapter describes how to set up and connect an RCM3200 series
module and the Prototyping Board included in the Development Kit.
NOTE: This chapter (and this manual) assume that you have the RCM3200 Development
Kit. If you purchased an RCM3200 series module by itself, you will have to adapt the
information in this chapter and elsewhere to your test and development setup.
2.1 Install Dynamic C
To develop and debug programs for an RCM3200 series RabbitCore module (and for all
other Rabbit hardware), you must install and use Dynamic C.
If you have not yet installed Dynamic C, do so now by inserting the Dynamic C CD from
the Development Kit in your PC’s CD-ROM drive. If autorun is enabled, the CD installa-
tion will begin automatically.
If autorun is disabled or the installation otherwise does not start, use the Windows
Start | Run
menu or Windows Disk Explorer to launch setup.exe from the root folder
of the CD-ROM.
The installation program will guide you through the installation process. Most steps of the
process are self-explanatory.
Dynamic C uses a COM (serial) port to communicate with the target development system.
The installation allows you to choose the COM port that will be used. The default selec-
tion is COM1. You may select any available port for Dynamic C’s use. If you are not cer-
tain which port is available, select COM1. This selection can be changed later within
Dynamic C.
NOTE: The installation utility does not check the selected COM port in any way. Speci-
fying a port in use by another device (mouse, modem, etc.) may lead to a message such
as "could not open serial port" when Dynamic C is started.
Once your installation is complete, you will have up to three icons on your PC desktop.
One icon is for Dynamic C, one opens the documentation menu, and the third is for the
Rabbit Field Utility, a tool used to download precompiled software to a target system.
If you have purchased the optional Dynamic C Rabbit Embedded Security Pack, install it
after installing Dynamic C. You must install the Rabbit Embedded Security Pack in the
same directory where Dynamic C was installed.
相關PDF資料 |
PDF描述 |
|---|---|
| 101-0525 | COMPUTER SINGLE-BOARD LP3500 FOX |
| 101-0602 | COMPUTER SNGL BRD BL2500 44.2MHZ |
| 101-0673 | MODULE RABBITCORE RCM3610 |
| 101-0814 | COMPUTER SNG BD BL1810 512K SRAM |
| 101-1007 | MODULE POWERCORE FLEX 3810 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 101-0522 | 功能描述:模塊化系統 - SOM MICRO-CNTLR DAUG/BD RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in |
| 10-105220-25P | 制造商:Amphenol Aerospace 功能描述:RECEPT |
| 10-105220-25S | 制造商:Amphenol Aerospace 功能描述:RECEPT |
| 10-105220-26P | 制造商:Amphenol Aerospace 功能描述:RECEPT |
| 10-105220-26S | 制造商:Amphenol Aerospace 功能描述:RECEPT |
發布緊急采購，3分鐘左右您將得到回復。