- 您現在的位置：買賣IC網 > PDF目錄3908 > 101-0558 (Rabbit Semiconductor)COMPUTER SNG BD BL1800 512K SRAM PDF資料下載
參數資料
| 型號： | 101-0558 |
| 廠商： | Rabbit Semiconductor |
| 文件頁數： | 43/94頁 |
| 文件大?。?/td> | 0K |
| 描述： | COMPUTER SNG BD BL1800 512K SRAM |
| 標準包裝： | 10 |
| 系列： | SBC |
| 模塊/板類型： | 單板計算機模塊 |
| 適用于相關產品： | BL1800 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁當前第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁
44
Jackrabbit (BL1800)
4.2.2 Other Sample Programs Illustrating Digital I/O
DEMOJR2.C
—repeatedly flashes LED DS3 (which is controlled by PA2) on the Proto-
typing Board.
This sample program also illustrates the use of the runwatch() function to allow
Dynamic C to update watch expressions while running. To test this:
1. Add a watch expression for "k" under "Inspect:Add/Del Watch Expression."
2. Click "Add to top" so that it will be permanently in the watch list.
3. While the program is running, type <Ctrl+U> to update the watch window.
DEMOJR3.C
—demonstrates the use of costatements to LED DS4 (which is controlled
by PA3) on the Prototyping Board. This sample program will also watch button S1
(PB2) and toggle LED DS1 (which is controlled by PA0) on/off when pressed. Note
that S1 presses are debounced by the software.
The pins on Parallel Port A can all be set as either outputs or as inputs via the slave port
control register (SPCTR). Do not use Parallel Port A if the slave port is being used.
Bits 0–5 on Parallel Port B are always inputs, and bits 6–7 are always outputs. Do not
use Parallel Port B if the slave port is being used.
JRIOTEST.C
—exercises the JackRabbit's four digital output channels, the one analog
input channel, and the two analog output channels.
JRIO_COF.C
—demonstrates the use of cofunctions with the analog input driver.
Before you run this sample program, connect DA1 to AD0 on header J7 of the Proto-
typing Board to provide an input voltage. Once the sample program is running, it will
read the input voltage ten times while another costatement is executed concurrently. The
values will be printed out in the Dynamic C STDIO window at the end of the program.
Before running the RABDB01.C and the RABDB02.C sample programs, you will need to
install 3 mm LEDs such as the Vishay Telefunken TLUR4400 at DS5–DS8 on the Jack-
rabbit Prototyping Board. These LEDs are included with the Jackrabbit Development Kit.
RABDB01.C
—flashes LEDs DS5–DS8 on the Jackrabbit Prototyping Board (which are
connected to PA4–PA7) when corresponding switches S1–S4 (which are connected to
PB2–PB5) are pressed. The buzzer, which is driven by HV0 from PE0, will also sound
whenever switch S1 switch is pressed.
RABDB02.C
—flashes LEDs DS5–DS8 on the Jackrabbit Prototyping Board (which are
connected to PA4–PA7) when corresponding switches S1–S4 (which are connected to
PB2–PB5) are pressed. The buzzer, which is driven by HV0 from PE0, will also sound
whenever switch S1 switch is pressed.
相關PDF資料 |
PDF描述 |
|---|---|
| 396-036-526-204 | CARD EDGE 36POS DL .125X.250 BLK |
| 396-036-526-202 | CARD EDGE 36POS DL .125X.250 BLK |
| 101-0411 | INTERFACE 12KEYDISP ETHNT OP6700 |
| AT24C02A-10PI-2.7 | IC EEPROM 2KBIT 400KHZ 8DIP |
| AT24C02A-10PI-1.8 | IC EEPROM 2KBIT 400KHZ 8DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 10105584 | 制造商:Amphenol Corporation 功能描述:10-341374-222 - Bulk |
| 101055OO | 制造商:TE Connectivity 功能描述: |
| 101056084S | 制造商:Amphenol Aerospace 功能描述:CONNECTOR |
| 101-0561 | 功能描述:模塊化系統 - SOM RCM3400 RABBITCORE RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in |
| 10-105610-02S | 制造商:Amphenol Aerospace 功能描述:PLUG |
發布緊急采購，3分鐘左右您將得到回復。