- 您現在的位置：買賣IC網 > PDF目錄3908 > 101-0558 (Rabbit Semiconductor)COMPUTER SNG BD BL1800 512K SRAM PDF資料下載
參數資料
| 型號： | 101-0558 |
| 廠商： | Rabbit Semiconductor |
| 文件頁數： | 53/94頁 |
| 文件大?。?/td> | 0K |
| 描述： | COMPUTER SNG BD BL1800 512K SRAM |
| 標準包裝： | 10 |
| 系列： | SBC |
| 模塊/板類型： | 單板計算機模塊 |
| 適用于相關產品： | BL1800 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁當前第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁
User’s Manual
53
The output value is set using the following function.
sets the state of an analog output channel.
jrioInit must be called first.
channel is the output channel number (0 or 1 on the Jackrabbit).
value is an integer from 0–1024 that corresponds to an output voltage as shown in Table 5.
NOTE: See the sample program JRIOTEST.C for examples of using the anaOut func-
tion.
Effect of Interrupts on Analog I/O
The stability of the voltage output (and hence the voltage input determination as well)
depends on the ability of the driver to respond quickly to interrupt requests. Dynamic C
debugging, use of the printf function, or any serial communications can disrupt the
pulse-width modulation utilized by the driver and cause fluctuations in the voltage out-
puts. Avoid using serial communications or printf statements during portions of your
program where the voltage must remain steady. Also be aware that debugging and running
Dynamic C in polling mode will cause fluctuations. Finally, be certain to disable the PWM
drivers by setting the output values to 0 or 1024 when you are done using them to free up
the CPU.
Calibration of Values to Voltages
The analog output channels on the Jackrabbit can be more accurately calibrated for each
individual Jackrabbit in the following manner (calibration of DA0 is assumed in this
example, calibration of DA1 would proceed similarly):
Set desired channel output to PWM_MIN.
Measure voltage Vmin on DA0.
Set desired channel output to PWM_MAX0.
Measure voltage Vmax on DA0.
A linear relation between input value and voltage can now be calculated:
Table 5. Typical Analog Output Voltages Corresponding
to Values in anaOut Function
Channel
0
PWM_MIN
PWM_MAX
1024
DA0
0.08 V
2.875 V
3.4 V
DA1
0.004 V
0.63 V
3.6 V
void anaOut(int channel, int value);
bVmax
m
PWM_MAX0
×
–
=
相關PDF資料 |
PDF描述 |
|---|---|
| 396-036-526-204 | CARD EDGE 36POS DL .125X.250 BLK |
| 396-036-526-202 | CARD EDGE 36POS DL .125X.250 BLK |
| 101-0411 | INTERFACE 12KEYDISP ETHNT OP6700 |
| AT24C02A-10PI-2.7 | IC EEPROM 2KBIT 400KHZ 8DIP |
| AT24C02A-10PI-1.8 | IC EEPROM 2KBIT 400KHZ 8DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 10105584 | 制造商:Amphenol Corporation 功能描述:10-341374-222 - Bulk |
| 101055OO | 制造商:TE Connectivity 功能描述: |
| 101056084S | 制造商:Amphenol Aerospace 功能描述:CONNECTOR |
| 101-0561 | 功能描述:模塊化系統 - SOM RCM3400 RABBITCORE RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in |
| 10-105610-02S | 制造商:Amphenol Aerospace 功能描述:PLUG |
發布緊急采購，3分鐘左右您將得到回復。