參數資料
型號： 101-0558
廠商： Rabbit Semiconductor
文件頁數： 51/94頁
文件大?。?/td> 0K
描述： COMPUTER SNG BD BL1800 512K SRAM
標準包裝： 10
系列： SBC
模塊/板類型： 單板計算機模塊
適用于相關產品： BL1800
User’s Manual
51
4.4 Jackrabbit Function Calls
4.4.1 I/O Drivers
The Jackrabbit contains four high-power digital output channels, two D/A converter out-
put channels, and one A/D converter input channel. These I/O channels can be accessed
using the functions found in the JRIO.LIB library.
4.4.1.1 Initialization
The function jrioInit() must be called before any other function from the JRIO.LIB
library. This function initializes the digital outputs and sets up the driver for the analog
input/outputs. The digital outputs correspond to the Rabbit processor’s port E bits 0–3, and
the analog I/O uses timer B; bits 1, 2, and 4 of port D; and bits 6 and 7 of port E.
The function void jrioInit() initializes the I/O drivers for Jackrabbit. In particular, it
sets up parallel port D bits 1, 2, and 4 for analog output, port E bits 0–3 for digital output,
and starts up the pulse-width modulation routines for the A/D and D/A channels. Note that
these routines can consume up to 20% of the CPU’s processing power; the routines use
timer B and the B1 and B2 match registers.
4.4.1.2 Digital Outputs
The Jackrabbit contains four high-power digital output drivers, HV0–HV3, on header J4.
These can be turned on and off with the following functions from the library JRIO.LIB.
HV0, HV1, and HV2 are open-collector sinking outputs, and are able to sink up to 1 A
(200 mA for the Jackrabbit and BL1820) from a 30 V source connected to the K line on
header J4. HV3 is a sourcing output that is able to source up to 500 mA (100 mA for the
BL1810 and BL1820) from a 30 V source connected to the K line.
CAUTION: Remember to cut the trace
between K and Vcc inside the outline
for header JP2 on the top side of the
Prototyping Board if you are supplying
K from a separate power supply. An
exacto knife, a precision grinder tool,
or a screwdriver may be used to cut
through the traces as shown in
NOTE: Failure to do this could lead to
the destruction of the Rabbit 2000
microprocessor and other components
once the Jackrabbit is connected to the
Prototyping Board.
Figure 16. Cut Trace on Prototyping Board
When Vcc and K Are Different
Cut gray trace
as shown
Cut
Buzzer
Top Side
Prototyping
Board
JP2
1
2
3
R3
R1
LS1
RT
1
BZR
VCC
K
AD0
PE4
POT
HV0 +RAW
COIL(-)
PD0
GND
AD0
+
JP2
K
VCC
相關PDF資料
PDF描述
396-036-526-204 CARD EDGE 36POS DL .125X.250 BLK
396-036-526-202 CARD EDGE 36POS DL .125X.250 BLK
101-0411 INTERFACE 12KEYDISP ETHNT OP6700
AT24C02A-10PI-2.7 IC EEPROM 2KBIT 400KHZ 8DIP
AT24C02A-10PI-1.8 IC EEPROM 2KBIT 400KHZ 8DIP
相關代理商/技術參數
參數描述
10105584 制造商:Amphenol Corporation 功能描述:10-341374-222 - Bulk
101055OO 制造商:TE Connectivity 功能描述:
101056084S 制造商:Amphenol Aerospace 功能描述:CONNECTOR
101-0561 功能描述:模塊化系統 - SOM RCM3400 RABBITCORE RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
10-105610-02S 制造商:Amphenol Aerospace 功能描述:PLUG
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*