參數資料
型號： 101-0599
廠商： Rabbit Semiconductor
文件頁數： 100/106頁
文件大?。?/td> 0K
描述： COMPUTER SNGLBD BL2500 512K FLSH
標準包裝： 10
系列： SBC
模塊/板類型： 單板計算機模塊
適用于相關產品： BL2500
User’s Manual
87
D.2 Physical Implementation
There are four signaling functions associated with a RabbitNet connection. From the mas-
ter’s point of view, the transmit function carries information and commands to the periph-
eral card. The receive function is used to read back information sent to the master by the
peripheral card. A clock is used to synchronize data going between the two devices at high
speed. The master is the source of this clock. A slave select (SS) function originates at the
master, and when detected by a peripheral card causes it to become selected and respond
to commands received from the master.
The signals themselves are differential RS-422, which are series-terminated at the source.
With this type of termination, the maximum frequency is limited by the round-trip delay
time of the cable. Although a peripheral card could theoretically be up to 45 m (150 ft)
from the master for a data rate of 1 MHz, Rabbit recommends a practical limit of 10 m
(33 ft).
Connections between peripheral cards and masters are done using standard 8-conductor
Ethernet cables. Masters and peripheral cards are equipped with RJ-45 8-pin female con-
nectors. The cables may be swapped end for end without affecting functionality.
D.2.1 Control and Routing
Control starts at the master when the master asserts the slave select signal (SS). Then it
simultaneously sends a serial command and clock. The first byte of a command contains
the address of the peripheral card if more than one peripheral card is connected.
A peripheral card assumes it is selected as soon as it receives the select signal. For direct
master-to-peripheral-card connections, this is as soon as the master asserts the select sig-
nal. The connection is established once the select signal reaches the addressed slave. At
this point communication between the master and the selected peripheral card is estab-
lished, and data can flow in both directions simultaneously. The connection is maintained
so long as the master asserts the select signal.
相關PDF資料
PDF描述
20-101-0497 MODULE OP6810 W/O ETH/MEM EXPANS
20-101-0464 COMPUTER SINGLE-BOARD BL2130
SOMOMAP3503-21-1670AGCR SYSTEM ON MODULE LV OMAP3503
101-0600 COMPUTER SNGLBD BL2510 512K FLSH
101-0575 COMPUTER SNGLBD BL2500 256K FLSH
相關代理商/技術參數
參數描述
10105D 制造商:MISCELLANEOUS 功能描述:
10105-DAP 制造商:MICRO DIMENSIONAL 功能描述: 制造商:MISCELLANEOUS 功能描述:
10105N 制造商:NXP Semiconductors 功能描述:
10105NA 制造商:NXP Semiconductors 功能描述:
10106 功能描述:WIRE STRIPPER AWG 10-30 RoHS:否 類別:工具 >> 剝線器和配件 系列:- 標準包裝:1 系列:- 類型:- 纜線類型:16~26 AWG 特點:-
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*