- 您現在的位置：買賣IC網 > PDF目錄3910 > 101-0599 (Rabbit Semiconductor)COMPUTER SNGLBD BL2500 512K FLSH PDF資料下載
參數資料
| 型號： | 101-0599 |
| 廠商： | Rabbit Semiconductor |
| 文件頁數： | 89/106頁 |
| 文件大小： | 0K |
| 描述： | COMPUTER SNGLBD BL2500 512K FLSH |
| 標準包裝： | 10 |
| 系列： | SBC |
| 模塊/板類型： | 單板計算機模塊 |
| 適用于相關產品： | BL2500 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁當前第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁
User’s Manual
77
B.2.1 Power to VRAM Switch
The VRAM switch on the Coyote’s RabbitCore module, shown in Figure B-2, allows the
battery backup to provide power when the external power goes off. The switch provides
an isolation between Vcc and the battery when Vcc goes low. This prevents the Vcc line
from draining the battery.
Figure B-2. VRAM Switch
The field-effect transistor provides a very small voltage drop between Vcc and VRAM
(<100 mV, typically 10 mV) so that the board components powered by Vcc will not have a
significantly different voltage than VRAM.
When the Coyote is not in reset, the RESOUT line will be high. This allows VRAM to
nearly equal Vcc.
When the Coyote is in reset, the RESOUT line will go low. This provides an isolation
between Vcc and VRAM.
B.2.2 Reset Generator
The Coyote’s RabbitCore module uses a reset generator to reset the Rabbit 3000 micro-
processor when the voltage drops below the voltage necessary for reliable operation. The
reset typically occurs at 2.93 V (2.63 V for the BL2510).
B.3 Chip Select Circuit
The current drain on the battery in a battery-backed circuit must be kept at a minimum.
When the Coyote is not powered, the battery keeps the SRAM memory contents and the
real-time clock (RTC) going. The SRAM has a powerdown mode that greatly reduces
power consumption. This powerdown mode is activated by raising the chip select (CS)
signal line. Normally the SRAM requires Vcc to operate. However, only 2 V is required
for data retention in powerdown mode. Thus, when power is removed from the circuit, the
battery voltage needs to be provided to both the SRAM power pin and to the CS signal
line. The CS control circuit accomplishes this task for the SRAM’s chip select signal line.
RESOUT
+3.3 V
VRAM
相關PDF資料 |
PDF描述 |
|---|---|
| 20-101-0497 | MODULE OP6810 W/O ETH/MEM EXPANS |
| 20-101-0464 | COMPUTER SINGLE-BOARD BL2130 |
| SOMOMAP3503-21-1670AGCR | SYSTEM ON MODULE LV OMAP3503 |
| 101-0600 | COMPUTER SNGLBD BL2510 512K FLSH |
| 101-0575 | COMPUTER SNGLBD BL2500 256K FLSH |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 10105D | 制造商:MISCELLANEOUS 功能描述: |
| 10105-DAP | 制造商:MICRO DIMENSIONAL 功能描述: 制造商:MISCELLANEOUS 功能描述: |
| 10105N | 制造商:NXP Semiconductors 功能描述: |
| 10105NA | 制造商:NXP Semiconductors 功能描述: |
| 10106 | 功能描述:WIRE STRIPPER AWG 10-30 RoHS:否 類別:工具 >> 剝線器和配件 系列:- 標準包裝:1 系列:- 類型:- 纜線類型:16~26 AWG 特點:- |
發布緊急采購，3分鐘左右您將得到回復。