參數資料
型號: 20-101-0434
廠商: Rabbit Semiconductor
文件頁數: 82/100頁
文件大?。?/td> 0K
描述: MODULE RABBITCORE RCM2100
標準包裝: 1
系列: RabbitCore®
模塊/板類型: MPU 核心模塊
適用于相關產品: RCM2100
其它名稱: 316-1085
Q3722620
Q3767195
Q3781474
Q4313544
Q4356478
Q4728021
Q5065239
Q5167294
Q5250689
Q5829428
76
RabbitCore RCM2100
B.3 Power Supply
The RCM2100 requires a regulated 5 V ± 0.25 V DC power source to operate. Depending
on the amount of current required by the application, different regulators can be used to
supply this voltage.
The Prototyping Board has an onboard LM340-T5 or equivalent. The LM340-T5 is an
inexpensive linear regulator that is easy to use. Its major drawback is its inefficiency,
which is directly proportional to the voltage drop across it. The voltage drop creates heat
and wastes power.
A switching power supply may be used in applications where better efficiency is desir-
able. The LM2575 is an example of an easy-to-use switcher. This part greatly reduces the
heat dissipation of the regulator. The drawback in using a switcher is the increased cost.
The Prototyping Board itself is protected against reverse polarity by a Shottky diode at D2
as shown in Figure B-3.
Figure B-3. Prototyping Board Power Supply
Capacitor C1 provides surge current protection for the voltage regulator, and allows the
external power supply to be located some distance away.
B.4 Using the Prototyping Board
The Prototyping Board is actually both a demonstration board and a prototyping board. As
a demonstration board, it can be used to demonstrate the functionality of the RCM2100
right out of the box without any modifications to either board. There are no jumpers or dip
switches to configure or misconfigure on the Prototyping Board so that the initial setup is
very straightforward.
The Prototyping Board comes with the basic components necessary to demonstrate the
operation of the RCM2100. Two LEDs (DS2 and DS3) are connected to PA0 and PA1, and
two switches (S2 and S3) are connected to PB2 and PB3 to demonstrate the interface to
the Rabbit 2000 microprocessor. Reset switch S1 is the hardware reset for the RCM2100.
Two more LEDs, driven by PA2 and PA3, may be added to the Prototyping Board for
additional outputs.
LINEAR POWER SUPPLY
POWER
IN
J5
100 nF
7805
U1
+RAW
DCIN
Vcc
C2
C1
1
2
3
1
2
3
1N5819
D2
10 mF
相關PDF資料
PDF描述
046232103103800 CONN FFC/FPC 3POS 1MM R/A SMD
355-030-521-204 CARDEDGE 30POS DL .156 LOPRO BLK
355-030-521-202 CARDEDGE 30POS DL .156 LOPRO BLK
355-030-521-201 CARDEDGE 30POS DL .156 LOPRO BLK
355-030-520-204 CARDEDGE 30POS DL .156 LOPRO BLK
相關代理商/技術參數
參數描述
20-101-0435 功能描述:模塊化系統 - SOM RCM2110 RabbitCore Module RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
20-101-0436 功能描述:模塊化系統 - SOM RCM2120 RabbitCore Module RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
20-101-0437 功能描述:子卡和OEM板 SR9205 16 in/8 out RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit
20-101-0439 功能描述:模塊化系統 - SOM SR9215 SRC 8IN 16OUT RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
20-101-0440 功能描述:模塊配件 SR9510 Relay 8 RoHS:否 制造商:Lantronix 產品: 用于: