參數資料
型號： 20-101-0492
廠商： Rabbit Semiconductor
文件頁數： 100/110頁
文件大?。?/td> 0K
描述： MODULE OP6800 FULL-FEATURED
標準包裝： 1
系列： SBC
模塊/板類型： 單板計算機模塊
適用于相關產品： OP6800
其它名稱： 20-101-492
20-101-492-ND
User’s Manual
5
1.4.1 Design Guidelines
Note the following requirements for incorporating the OP6800 operator interfaces into
your application to comply with CE requirements.
General
The power supply provided with the Tool Kit is for development purposes only. It is the
customer’s responsibility to provide a CE-compliant power supply for the end-product
application.
When connecting the OP6800 to outdoor cables, the customer is responsible for provid-
ing CE-approved surge/lightning protection.
Rabbit recommends placing digital I/O or analog cables that are 3 m or longer in a
metal conduit to assist in maintaining CE compliance and to conform to good cable
design practices. Rabbit also recommends using properly shielded I/O cables in noisy
electromagnetic environments.
While the OP6800 meets the EN61000-4-2 (ESD) requirements in that it can withstand
contact discharges of ± 4 kV and air discharges of ± 8 kV, it is the responsibility of the
end-user to use proper ESD precautions to prevent ESD damage when installing or ser-
vicing the OP6800.
Safety
For personal safety, all inputs and outputs to and from the OP6800 must not be con-
nected to voltages exceeding SELV levels (42.4 V AC peak, or 60 V DC). Damage to
the Rabbit 2000 microprocessor may result if voltages outside the design range of 0 V
to 40 V DC are applied directly to any of its digital inputs.
The lithium backup battery circuit on the OP6800 has been designed to protect the bat-
tery from hazardous conditions such as reverse charging and excessive current flows.
Do not disable the safety features of the design.
1.4.2 Interfacing the OP6800 to Other Devices
Since the OP6800 operator control panels are designed to be connected to other devices,
good EMC practices should be followed to ensure compliance. CE compliance is ulti-
mately the responsibility of the integrator. Additional information, tips, and technical
assistance are available from your authorized Rabbit distributor, and are also available on
our Web site at www.rabbit.com.
相關PDF資料
PDF描述
101-0492 INTERFACE OP6800 W/ETHERNET PORT
11FMN-BMTR-A-TB CONN FMN HSNG 11POS SGL REV SMD
11FMN-BMT-A-TF CONN FMN HSNG 11POS SNGL NOR SMD
AT24C01-10SI-2.7 IC EEPROM 1KBIT 400KHZ 8SOIC
AT24C01-10PI-2.7 IC EEPROM 1KBIT 400KHZ 8DIP
相關代理商/技術參數
參數描述
20-101-0494 功能描述:模塊化系統 - SOM RCM2250 RabbitCore Module RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
20-101-0495 功能描述:處理器配件 BASEPLATE RoHS:否 制造商:Olimex Ltd. 產品:Cable 用于:
20-101-0497 功能描述:單板計算機 OP6810 RoHS:否 制造商:Ampro By ADLINK 外觀尺寸:EPIC 處理器類型:Intel Atom D510 頻率:1.66 GHz 存儲容量:2 GB (max) 存儲類型:DDR2, L2 Cache 接口類型:Ethernet, PS/2, SATA, Serial, USB 工作電源電壓:5 V, 12 V 功耗:13 W 最大工作溫度:+ 70 C 尺寸:165.1 mm x 114.3 mm
201-01050 功能描述:鋁質電解電容器 - 帶引線 1 uF Electrolytic Capacitor RoHS:否 制造商:Kemet 引線類型: 電容:220 uF 容差:20 % 電壓額定值:25 V 工作溫度范圍: 端接類型:Radial 外殼直徑:8 mm 外殼長度:11 mm 引線間隔:5 mm 產品:General Purpose Electrolytic Capacitors 封裝:Bulk
201-0105-01 功能描述:印刷電路板和試驗板 JTAG 20 Pin Connector RoHS:否 制造商:3M Electronic Solutions Division 產品:Jumper & Insulated Wires 描述/功能:Jumper wire, 22 AWG 0.1 inch 長度:0.1 in 寬度:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*