參數資料
型號： 20-101-0492
廠商： Rabbit Semiconductor
文件頁數： 74/110頁
文件大小： 0K
描述： MODULE OP6800 FULL-FEATURED
標準包裝： 1
系列： SBC
模塊/板類型： 單板計算機模塊
適用于相關產品： OP6800
其它名稱： 20-101-492
20-101-492-ND
62
MiniCom (OP6800)
B.3 Chip Select Circuit
Figure B-1 shows a schematic of the chip select circuit located on the OP6800 module.
Figure B-1. Chip Select Circuit
The current drain on the battery in a battery-backed circuit must be kept at a minimum.
When the OP6800 is not powered, the battery keeps the SRAM memory contents and the
real-time clock (RTC) going. The SRAM has a powerdown mode that greatly reduces
power consumption. This powerdown mode is activated by raising the chip select (CS)
signal line. Normally the SRAM requires Vcc to operate. However, only 2 V is required
for data retention in powerdown mode. Thus, when power is removed from the circuit, the
battery voltage needs to be provided to both the SRAM power pin and to the CS signal
line. The CS control circuit accomplishes this task for the SRAM’s chip select signal line.
In a powered-up condition, the CS control circuit must allow the processor’s chip select
signal /CS1 to control the SRAM’s CS signal /CSRAM. So, with power applied, /CSRAM
must be the same signal as /CS1, and with power removed, /CSRAM must be held high
(but only needs to be battery voltage high). Q3 and Q4 are MOSFET transistors with com-
plementary polarity. They are both turned on when power is applied to the circuit. They
allow the CS signal to pass from the processor to the SRAM so that the processor can peri-
odically access the SRAM. When power is removed from the circuit, the transistors will
turn off and isolate /CSRAM from the processor. The isolated /CSRAM line has a 100 k
pullup resistor to VRAM (R28). This pullup resistor keeps /CSRAM at the VRAM voltage
level (which under no power condition is the backup battery’s regulated voltage at a little
more than 2 V).
Transistors Q3 and Q4 are of opposite polarity so that a rail-to-rail voltage can be passed.
When the /CS1 voltage is low, Q3 will conduct. When the /CS1 voltage is high, Q4 con-
ducts. It takes time for the transistors to turn on, creating a propagation delay. This propa-
gation delay is typically very small, about 10 ns to 15 ns.
/CS1
/CSRAM
/RESET_OUT
Q3
Q4
R28
VRAM
100 kW
VRAM
SWITCH
相關PDF資料
PDF描述
101-0492 INTERFACE OP6800 W/ETHERNET PORT
11FMN-BMTR-A-TB CONN FMN HSNG 11POS SGL REV SMD
11FMN-BMT-A-TF CONN FMN HSNG 11POS SNGL NOR SMD
AT24C01-10SI-2.7 IC EEPROM 1KBIT 400KHZ 8SOIC
AT24C01-10PI-2.7 IC EEPROM 1KBIT 400KHZ 8DIP
相關代理商/技術參數
參數描述
20-101-0494 功能描述:模塊化系統 - SOM RCM2250 RabbitCore Module RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
20-101-0495 功能描述:處理器配件 BASEPLATE RoHS:否 制造商:Olimex Ltd. 產品:Cable 用于:
20-101-0497 功能描述:單板計算機 OP6810 RoHS:否 制造商:Ampro By ADLINK 外觀尺寸:EPIC 處理器類型:Intel Atom D510 頻率:1.66 GHz 存儲容量:2 GB (max) 存儲類型:DDR2, L2 Cache 接口類型:Ethernet, PS/2, SATA, Serial, USB 工作電源電壓:5 V, 12 V 功耗:13 W 最大工作溫度:+ 70 C 尺寸:165.1 mm x 114.3 mm
201-01050 功能描述:鋁質電解電容器 - 帶引線 1 uF Electrolytic Capacitor RoHS:否 制造商:Kemet 引線類型: 電容:220 uF 容差:20 % 電壓額定值:25 V 工作溫度范圍: 端接類型:Radial 外殼直徑:8 mm 外殼長度:11 mm 引線間隔:5 mm 產品:General Purpose Electrolytic Capacitors 封裝:Bulk
201-0105-01 功能描述:印刷電路板和試驗板 JTAG 20 Pin Connector RoHS:否 制造商:3M Electronic Solutions Division 產品:Jumper & Insulated Wires 描述/功能:Jumper wire, 22 AWG 0.1 inch 長度:0.1 in 寬度:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*