參數資料
型號： 20-101-0497
廠商： Rabbit Semiconductor
文件頁數： 19/110頁
文件大?。?/td> 0K
描述： MODULE OP6810 W/O ETH/MEM EXPANS
標準包裝： 1
系列： SBC
模塊/板類型： 單板計算機模塊
適用于相關產品： OP6810
其它名稱： 20-101-497
20-101-497-ND
12
MiniCom (OP6800)
2.5 Installing Dynamic C
If you have not yet installed Dynamic C version 7.06P2 (or a later version), do so now by
inserting the Dynamic C CD in your PC’s CD-ROM drive. The CD will auto-install unless
you have disabled auto-install on your PC.
If the CD does not auto-install, click Start > Run from the Windows Start button and
browse for the Dynamic C setup.exe file on your CD drive. Click OK to begin the
installation once you have selected the setup.exe file.
The Dynamic C User’s Manual provides detailed instructions for the installation of
Dynamic C and any future upgrades.
NOTE: If you have an earlier version of Dynamic C already installed, the default instal-
lation of the later version will be in a different folder, and a separate icon will appear on
your desktop.
2.6 Starting Dynamic C
Once the OP6800 is connected to your PC and to a power source, start Dynamic C by dou-
ble-clicking on the Dynamic C icon on your desktop or in your Start menu.
If you are using a USB port to connect your computer to the OP6800, choose Options >
Project Options
and select “Use USB to Serial Converter.” Click OK.
Dynamic C assumes, by default, that you are using serial port COM1 on your PC. If you
are using COM1, then Dynamic C should detect the OP6800 and go through a sequence of
steps to cold-boot the OP6800 and to compile the BIOS. If the error message “Rabbit Pro-
cessor Not Detected” appears, you have probably connected to a different PC serial port
such as COM2, COM3, or COM4. You can change the serial port used by Dynamic C with
the OPTIONS menu, then try to get Dynamic C to recognize the OP6800 by selecting
Reset Target/Compile BIOS
on the Compile menu. Try the different COM ports in the
OPTIONS
menu until you find the one you are connected to. If you still can’t get Dynamic
C to recognize the target on any port, then the hookup may be wrong or the COM port
might not working on your PC.
If you receive the “BIOS successfully compiled …” message after pressing <Ctrl-Y> or
starting Dynamic C, and this message is followed by a communications error message, it
is possible that your PC cannot handle the 115,200 bps baud rate. Try changing the baud
rate to 57,600 bps as follows.
Locate the Serial Options dialog in the Dynamic C Options > Project Options >
Communications
menu. Change the baud rate to 57,600 bps.
相關PDF資料
PDF描述
20-101-0464 COMPUTER SINGLE-BOARD BL2130
SOMOMAP3503-21-1670AGCR SYSTEM ON MODULE LV OMAP3503
101-0600 COMPUTER SNGLBD BL2510 512K FLSH
101-0575 COMPUTER SNGLBD BL2500 256K FLSH
20-101-0526 COMPUTER SNGLBD LP3510 FOX7.4MHZ
相關代理商/技術參數
參數描述
201-01050 功能描述:鋁質電解電容器 - 帶引線 1 uF Electrolytic Capacitor RoHS:否 制造商:Kemet 引線類型: 電容:220 uF 容差:20 % 電壓額定值:25 V 工作溫度范圍: 端接類型:Radial 外殼直徑:8 mm 外殼長度:11 mm 引線間隔:5 mm 產品:General Purpose Electrolytic Capacitors 封裝:Bulk
201-0105-01 功能描述:印刷電路板和試驗板 JTAG 20 Pin Connector RoHS:否 制造商:3M Electronic Solutions Division 產品:Jumper & Insulated Wires 描述/功能:Jumper wire, 22 AWG 0.1 inch 長度:0.1 in 寬度:
20-101-0502 功能描述:處理器配件 Keypad/Display Unit 5V Panle Mount RoHS:否 制造商:Olimex Ltd. 產品:Cable 用于:
20-101-0504 功能描述:程序設計器配件 Cable KDU w/mount Hardware RoHS:否 制造商:Lattice 產品:ispDOWNLOAD Cables 用于:In-system Programming
20-101-0506 功能描述:單板計算機 SR9160 CPU Card RoHS:否 制造商:Ampro By ADLINK 外觀尺寸:EPIC 處理器類型:Intel Atom D510 頻率:1.66 GHz 存儲容量:2 GB (max) 存儲類型:DDR2, L2 Cache 接口類型:Ethernet, PS/2, SATA, Serial, USB 工作電源電壓:5 V, 12 V 功耗:13 W 最大工作溫度:+ 70 C 尺寸:165.1 mm x 114.3 mm
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*