參數資料
型號: 20-101-0497
廠商: Rabbit Semiconductor
文件頁數: 49/110頁
文件大小: 0K
描述: MODULE OP6810 W/O ETH/MEM EXPANS
標準包裝: 1
系列: SBC
模塊/板類型: 單板計算機模塊
適用于相關產品: OP6810
其它名稱: 20-101-497
20-101-497-ND
User’s Manual
39
5.2 TCP/IP Sample Programs
We have provided a number of sample programs demonstrating various uses of TCP/IP for
networking embedded systems. These programs require that you connect your PC and the
OP6800 together on the same network. This network can be a local private network (pre-
ferred for initial experimentation and debugging), or a connection via the Internet.
5.2.1 How to Set IP Addresses in the Sample Programs
With the introduction of Dynamic C 7.30 we have taken steps to make it easier to run
many of our sample programs. You will see a TCPCONFIG macro. This macro tells
Dynamic C to select your configuration from a list of default configurations. You will
have three choices when you encounter a sample program with the TCPCONFIG macro.
1. You can replace the TCPCONFIG macro with individual MY_IP_ADDRESS,
MY_NETMASK
, MY_GATEWAY, and MY_NAMESERVER macros in each program.
2. You can leave TCPCONFIG at the usual default of 1, which will set the IP configurations
to 10.10.6.100, the netmask to 255.255.255.0, and the nameserver and gateway
to 10.10.6.1. If you would like to change the default values, for example, to use an IP
address of 10.1.1.2 for the Coyote board, and 10.1.1.1 for your PC, you can edit
the values in the section that directly follows the “General Configuration” comment in
the TCP_CONFIG.LIB library. You will find this library in the LIB\TCPIP directory.
3. You can create a CUSTOM_CONFIG.LIB library and use a TCPCONFIG value greater
than 100. Instructions for doing this are at the beginning of the TCP_CONFIG.LIB
library in the LIB\TCPIP directory.
There are some other “standard” configurations for TCPCONFIG that let you select differ-
ent features such as DHCP. Their values are documented at the top of the
TCP_CONFIG.LIB
library in the LIB\TCPIP directory. More information is available in
the Dynamic C TCP/IP User’s Manual.
IP Addresses Before Dynamic C 7.30
Most of the sample programs use macros to define the IP address assigned to the board
and the IP address of the gateway, if there is a gateway.
#define MY_IP_ADDRESS "216.112.116.155"
#define MY_NETMASK "255.255.255.248"
#define MY_GATEWAY "216.112.116.153"
In order to do a direct connection, the following IP addresses can be used for the OP6800:
#define MY_IP_ADDRESS "10.1.1.2"
#define MY_NETMASK "255.255.255.248"
// #define MY_GATEWAY "216.112.116.153"
In this case, the gateway is not used and is commented out. The IP address of the board is
defined to be 10.1.1.2. The IP address of your PC can be defined as 10.1.1.1.
相關PDF資料
PDF描述
20-101-0464 COMPUTER SINGLE-BOARD BL2130
SOMOMAP3503-21-1670AGCR SYSTEM ON MODULE LV OMAP3503
101-0600 COMPUTER SNGLBD BL2510 512K FLSH
101-0575 COMPUTER SNGLBD BL2500 256K FLSH
20-101-0526 COMPUTER SNGLBD LP3510 FOX7.4MHZ
相關代理商/技術參數
參數描述
201-01050 功能描述:鋁質電解電容器 - 帶引線 1 uF Electrolytic Capacitor RoHS:否 制造商:Kemet 引線類型: 電容:220 uF 容差:20 % 電壓額定值:25 V 工作溫度范圍: 端接類型:Radial 外殼直徑:8 mm 外殼長度:11 mm 引線間隔:5 mm 產品:General Purpose Electrolytic Capacitors 封裝:Bulk
201-0105-01 功能描述:印刷電路板和試驗板 JTAG 20 Pin Connector RoHS:否 制造商:3M Electronic Solutions Division 產品:Jumper & Insulated Wires 描述/功能:Jumper wire, 22 AWG 0.1 inch 長度:0.1 in 寬度:
20-101-0502 功能描述:處理器配件 Keypad/Display Unit 5V Panle Mount RoHS:否 制造商:Olimex Ltd. 產品:Cable 用于:
20-101-0504 功能描述:程序設計器配件 Cable KDU w/mount Hardware RoHS:否 制造商:Lattice 產品:ispDOWNLOAD Cables 用于:In-system Programming
20-101-0506 功能描述:單板計算機 SR9160 CPU Card RoHS:否 制造商:Ampro By ADLINK 外觀尺寸:EPIC 處理器類型:Intel Atom D510 頻率:1.66 GHz 存儲容量:2 GB (max) 存儲類型:DDR2, L2 Cache 接口類型:Ethernet, PS/2, SATA, Serial, USB 工作電源電壓:5 V, 12 V 功耗:13 W 最大工作溫度:+ 70 C 尺寸:165.1 mm x 114.3 mm