參數資料
型號: 20-101-1055
廠商: Rabbit Semiconductor
文件頁數: 106/164頁
文件大?。?/td> 0K
描述: MODULE RABBITCORE RCM3375
標準包裝: 1
系列: RabbitCore®
模塊/板類型: MPU 核心模塊
適用于相關產品: RCM3375
其它名稱: 316-1112
40
RabbitCore RCM3365/RCM3375
4.5 Other Hardware
4.5.1 Clock Doubler
The RCM3365/RCM33610 takes advantage of the Rabbit 3000 microprocessor’s internal
clock doubler. A built-in clock doubler allows half-frequency crystals to be used to reduce
radiated emissions. The 44.2 MHz frequency specified for the RCM3365/RCM3375 is
generated using a 22.12 MHz resonator.
The clock doubler may be disabled if 44.2 MHz clock speeds are not required. This will
reduce power consumption and further reduce radiated emissions. The clock doubler is
disabled with a simple configuration macro as shown below.
4.5.2 Spectrum Spreader
The Rabbit 3000 features a spectrum spreader, which helps to mitigate EMI problems. The
spectrum spreader is on by default, but it may also be turned off or set to a stronger setting.
The means for doing so is through a simple configuration macro as shown below.
NOTE: Refer to the Rabbit 3000 Microprocessor User’s Manual for more information
on the spectrum-spreading setting and the maximum clock speed.
1. Select the “Defines” tab from the Dynamic C Options > Project Options menu.
2. Add the line CLOCK_DOUBLED=0 to always disable the clock doubler.
The clock doubler is enabled by default, and usually no entry is needed. If you need to
specify that the clock doubler is always enabled, add the line CLOCK_DOUBLED=1 to
always enable the clock doubler.
3. Click OK to save the macro. The clock doubler will now remain off whenever you are
in the project file where you defined the macro.
1. Select the “Defines” tab from the Dynamic C Options > Project Options menu.
2. Normal spreading is the default, and usually no entry is needed. If you need to specify
normal spreading, add the line
ENABLE_SPREADER=1
For strong spreading, add the line
ENABLE_SPREADER=2
To disable the spectrum spreader, add the line
ENABLE_SPREADER=0
NOTE: The strong spectrum-spreading setting is not recommended since it may limit
the maximum clock speed or the maximum baud rate. It is unlikely that the strong set-
ting will be used in a real application.
3. Click OK to save the macro. The spectrum spreader will now be set to the state specified
by the macro value whenever you are in the project file where you defined the macro.
相關PDF資料
PDF描述
20-101-0434 MODULE RABBITCORE RCM2100
046232103103800 CONN FFC/FPC 3POS 1MM R/A SMD
355-030-521-204 CARDEDGE 30POS DL .156 LOPRO BLK
355-030-521-202 CARDEDGE 30POS DL .156 LOPRO BLK
355-030-521-201 CARDEDGE 30POS DL .156 LOPRO BLK
相關代理商/技術參數
參數描述
20-101-1066 功能描述:模塊化系統 - SOM RCM3720 PROTO RS232 RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
20-101-1067 功能描述:模塊化系統 - SOM RCM3305 MODULE RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
20-101-1068 功能描述:模塊化系統 - SOM RCM3315 MODULE RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
20-101-1087 制造商:Digi International 功能描述:RCM3365 RABBITSYS - Bulk 制造商:Digi International Inc 功能描述:BOARD PROTO RCM3365 RS232 制造商:Rabbit Semiconductor 功能描述:RCM3365 Rabbit Sys
20-101-1093 功能描述:模塊化系統 - SOM RCM4110 RABBIT CORE MODULE RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in