- 您現在的位置：買賣IC網 > PDF目錄371388 > 2486 (Linear Technology Corporation) 16-Bit 2-/4-Channel ツヒ ADC with PGA and Easy Drive Input Current Cancellation PDF資料下載
參數資料
| 型號： | 2486 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | 16-Bit 2-/4-Channel ツヒ ADC with PGA and Easy Drive Input Current Cancellation |
| 中文描述： | 16位2-/4-ChannelツヒADC，帶PGA和簡易輸入電流驅動取消 |
| 文件頁數： | 11/36頁 |
| 文件大?。?/td> | 596K |
| 代理商： | 2486 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
LTC2486
11
2486f
PIN FUNCTIONS
F
O
(Pin 1):
Frequency Control Pin. Digital input that controls
the internal conversion clock rate. When F
O
is connected
to GND, the converter uses its internal oscillator running at
307.2kHz. The conversion clock may also be overridden by
driving the F
O
pin with an external clock in order to change
the output rate and the digital filter rejection null.
SDI (Pin 2):
Serial Data Input. This pin is used to select
the gain, line frequency rejection mode, 1x or 2x speed
mode, temperature sensor, as well as the input channel.
The serial data input is applied under control of the serial
clock (SCK) during the data output/input operation. The
first conversion following a new input or mode change
is valid.
SCK (Pin 3):
Bidirectional, Digital I/O, Clock Pin. In Internal
Serial Clock Operation mode, SCK is generated internally
and is seen as an output on the SCK pin. In External Serial
Clock Operation mode, the digital I/O clock is externally
applied to the SCK pin. The Serial Clock operation mode
is determined by the logic level applied to the SCK pin at
power up and during the most recent falling edge of
C
S.
C
S (Pin 4):
Active LOW Chip Select. A LOW on this pin
enables the digital input/output and wakes up the ADC.
Following each conversion, the ADC automatically enters
the Sleep mode and remains in this low power state as
long as
C
S is HIGH. A LOW-to-HIGH transition on
C
S
during the data output aborts the data transfer and starts
a new conversion.
SDO (Pin 5):
Three-State Digital Output. During the data
output period, this pin is used as the serial data output.
When the chip select pin is HIGH, the SDO pin is in a high
impedance state. During the conversion and sleep periods,
this pin is used as the conversion status output. When
the conversion is in progress this pin is HIGH; once the
conversion is complete SDO goes low. The conversion
status is monitored by pulling
C
S LOW.
GND (Pin 6):
Ground. Connect this pin to a common ground
plane through a low impedance connection.
COM (Pin 7):
The common negative input (IN
–
) for all
single ended multiplexer configurations. The voltage on
CH0 to CH3 and COM pins can have any value between
GND – 0.3V to V
CC
+ 0.3V. Within these limits, the two
selected inputs (IN
+
and IN
–
) provide a bipolar input range
V
IN
= (IN
+
– IN
–
) from –0.5 V
REF
/Gain to 0.5 V
REF
/Gain.
Outside this input range, the converter produces unique
over-range and under-range output codes.
CH0 to CH3 (Pins 8-11):
Analog Inputs. May be pro-
grammed for single-ended or differential mode.
V
CC
(Pin 12):
Positive Supply Voltage. Bypass to GND with
a 10μF tantalum capacitor in parallel with a 0.1μF ceramic
capacitor as close to the part as possible.
REF
+
(Pin 13), REF
–
(Pin 14):
Differential Reference Input.
The voltage on these pins can have any value between
GND and V
CC
as long as the reference positive input,
REF
+
, remains more positive than the negative reference
input, REF
–
, by at least 0.1V. The differential voltage V
REF
= (REF
+
– REF
–
) sets the full-scale range (
–0.5 V
REF
/Gain
to 0.5 V
REF
/Gain)
for all input channels.
Exposed Pad (Pin 15):
Ground. This pin is ground and
must be soldered to the PCB ground plane. For prototyping
purposes, this pin may remain floating.
相關PDF資料 |
PDF描述 |
|---|---|
| 2495 | 16-Bit 8-/16-Channel ツヒ ADC with PGA, Easy Drive and I2C Interface |
| 249NQ | SCHOTTKY RECTIFIER |
| 249NQ135 | SCHOTTKY RECTIFIER |
| 249NQ135R | SCHOTTKY RECTIFIER |
| 249NQ150 | SCHOTTKY RECTIFIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 2486 01 | 制造商:Lumberg Connect GmbH 功能描述:MINI USB TYPE B RECEPTACLE SMT 制造商:LUMBERG 功能描述:MINI USB TYPE B, RECEPTACLE, SMT 制造商:LUMBERG 功能描述:MINI USB CONNECTOR, RCPT, 5POS, SOLDER; Connector Type:USB Mini B; Series:-; Gender:Receptacle; No. of Contacts:5; Contact Termination:Surface Mount Right Angle; Connector Mounting:PCB; Contact Plating:Gold; Voltage AC:5V ;RoHS Compliant: Yes 制造商:Lumberg 功能描述:Conn Mini USB Type B PL 5 POS Solder RA SMD 5 Terminal 1 Port Bulk |
| 2486 01 VP3 | 制造商:Lumberg Connect GmbH 功能描述:Conn Mini USB Type B PL 5 POS Solder RA SMD 5 Terminal 1 Port Bulk |
| 2486 03 VP3 | 制造商:Lumberg 功能描述:CONN MINI USB TYPE B PL 5 POS SOLDER RA SMD 5 TERMINAL 1 PORT BULK USB 2.0 |
| 24-8600-310C | 功能描述:IC 與器件插座 ELEV. SCKT .3 CENTER COLLET 24 PINS RoHS:否 制造商:Molex 產品:LGA Sockets 節距:1.02 mm 排數: 位置/觸點數量:2011 觸點電鍍:Gold 安裝風格:SMD/SMT 端接類型:Solder 插座/封裝類型:LGA 2011 工作溫度范圍:- 40 C to + 100 C |
| 24-8600-610C | 功能描述:IC 與器件插座 ELEV. SCKT .3 CENTER COLLET 24 PINS RoHS:否 制造商:Molex 產品:LGA Sockets 節距:1.02 mm 排數: 位置/觸點數量:2011 觸點電鍍:Gold 安裝風格:SMD/SMT 端接類型:Solder 插座/封裝類型:LGA 2011 工作溫度范圍:- 40 C to + 100 C |
發布緊急采購，3分鐘左右您將得到回復。