- 您現在的位置：買賣IC網 > PDF目錄371394 > 24C02SC (Microchip Technology Inc.) 2K 5.0V IIC serial EEPROMs(2.5V~5.5V,2K位,1M次擦寫周期,ISO7816標準) PDF資料下載
參數資料
| 型號： | 24C02SC |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | 2K 5.0V IIC serial EEPROMs(2.5V~5.5V,2K位,1M次擦寫周期,ISO7816標準) |
| 中文描述： | 2K 5.0V國際進口電壓（2.5V?5.5V的和2K位，100萬次擦寫周期，符合ISO7816標準串行EEPROM） |
| 文件頁數： | 27/170頁 |
| 文件大小： | 4191K |
| 代理商： | 24C02SC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁
2003 Microchip Technology Inc.
Preliminary
DS40300C-page 25
PIC16F62X
3.3
PCL and PCLATH
The program counter (PC) is 13-bits wide. The low byte
comes from the PCL register, which is a readable and
writable register. The high byte (PC<12:8>) is not
directly readable or writable and comes from PCLATH.
On any RESET, the PC is cleared. Figure 3-3 shows
the two situations for the loading of the PC. The upper
example in the figure shows how the PC is loaded on a
write to PCL (PCLATH<4:0>
→
PCH). The lower exam-
ple in the figure shows how the PC is loaded during a
CALL
or
GOTO
instruction (PCLATH<4:3>
→
PCH).
FIGURE 3-3:
LOADING OF PC IN
DIFFERENT SITUATIONS
3.3.1
COMPUTED GOTO
A computed
GOTO
is accomplished by adding an offset
to the program counter (
ADDWF PCL
). When doing a
table read using a computed
GOTO
method, care
should be exercised if the table location crosses a PCL
memory boundary (each 256 byte block). Refer to the
application note
“Implementing a Table Read”
(AN556).
3.3.2
STACK
The PIC16F62X family has an 8-level deep x 13-bit
wide hardware stack (Figure 3-1 and Figure 3-2). The
stack space is not part of either program or data space
and the stack pointer is not readable or writable. The
PC is PUSHed onto the stack when a
CALL
instruction
is executed or an interrupt causes a branch. The stack
is POPed in the event of a
RETURN, RETLW
or a
RETFIE
instruction execution. PCLATH is not affected
by a PUSH or POP operation.
The stack operates as a circular buffer. This means that
after the stack has been PUSHed eight times, the ninth
push overwrites the value that was stored from the first
push. The tenth push overwrites the second push (and
so on).
3.4
Indirect Addressing, INDF and
FSR Registers
The INDF register is not a physical register. Addressing
the INDF register will cause indirect addressing.
Indirect addressing is possible by using the INDF
register. Any instruction using the INDF register actu-
ally accesses data pointed to by the file select register
(FSR). Reading INDF itself indirectly will produce 00h.
Writing to the INDF register indirectly results in a no-
operation (although STATUS bits may be affected). An
effective 9-bit address is obtained by concatenating the
8-bit FSR register and the IRP bit (STATUS<7>), as
shown in Figure 3-4.
A simple program to clear RAM location 20h-2Fh using
indirect addressing is shown in Example 3-1.
EXAMPLE 3-1:
Indirect Addressing
movlw
movwf
clrf
incf
btfss
goto
0x20
FSR
INDF
FSR
FSR,4
NEXT
;initialize pointer
;to RAM
;clear INDF register
;inc pointer
;all done
;no clear next
;yes continue
NEXT
PC
12
8
7
0
5
PCLATH<4:0>
PCLATH
Instruction with
PCL as
Destination
ALU result
GOTO, CALL
Opcode <10:0>
8
PC
12
11 10
0
11
PCLATH<4:3>
PCH
PCL
8
7
2
PCLATH
PCH
PCL
Note 1:
There are no STATUS bits to indicate
stack
overflow
conditions.
or
stack
underflow
2:
There are no instructions/mnemonics
called PUSH or POP. These are actions
that occur from the execution of the
CALL, RETURN, RETLW
and
RETFIE
instructions, or the vectoring to an
interrupt address.
相關PDF資料 |
PDF描述 |
|---|---|
| 24C02A | 2K 5.0V CMOS serial EEPROMs(2K位,5.0V,IIC串行EEPROM) |
| 24C02C | 2K 5.0V IIC serial EEPROMs(2K位，1M次擦寫周期，硬件寫保護，二線串行接口,EEPROM) |
| 24C02C-EP | 2K 5.0V I 2 C ⑩ Serial EEPROM |
| 24C02C-ESN | 2K 5.0V I 2 C ⑩ Serial EEPROM |
| 24C02C-EST | 2K 5.0V I 2 C ⑩ Serial EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 24C02SC/S | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SERIAL EEPROM|256X8|CMOS|DIE |
| 24C02SC-/S | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:1K/2K 5.0V I2C Serial EEPROMs for Smart Cards |
| 24C02SC/S08 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SERIAL EEPROM|256X8|CMOS|DIE |
| 24C02SC-/S08 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:1K/2K 5.0V I2C Serial EEPROMs for Smart Cards |
| 24C02SC/W | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SERIAL EEPROM|256X8|CMOS|WAFER |
發布緊急采購，3分鐘左右您將得到回復。