- 您現在的位置：買賣IC網 > PDF目錄368957 > 28F016S3 Evaluation Kit for the MAX5950/MAX5951 PDF資料下載
參數資料
| 型號： | 28F016S3 |
| 英文描述： | Evaluation Kit for the MAX5950/MAX5951 |
| 中文描述： | 字節寬的SMART 3 FlashFile Memory系列4。 8。及16兆比特 |
| 文件頁數： | 10/59頁 |
| 文件大?。?/td> | 384K |
| 代理商： | 28F016S3 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁
3 VOLT ADVANCED+ BOOT BLOCK
E
10
PRODUCT PREVIEW
Table 2. 3 Volt Advanced+ Boot Block Pin Descriptions
(Continued)
Symbol
Type
Name and Function
V
CCQ
INPUT
I/O POWER SUPPLY:
Supplies power for input/output buffers.
[2.7 V
–3.6 V] This input should be tied directly to V
CC
.
[1.65 V– 2.5 V] Lower I/O power supply voltage available upon request.
Contact your Intel representative for more information.
V
PP
INPUT/
SUPPLY
PROGRAM/ERASE POWER SUPPLY:
[1.65 V–3.6 V or 11.4 V–12.6 V]
Operates as a input at logic levels to control complete device protection.
Supplies power for accelerated program and erase operations in 12 V
±
5% range. This pin cannot be left floating.
Lower
V
PP
≤
V
PPLK
, to protect all contents
against Program and
Erase commands.
Set V
PP
= V
CC
for in-system read, program and erase operations
. In
this configuration, V
PP
can drop as low as 1.65 V to allow for resistor or
diode drop from the system supply. Note that if V
PP
is driven by a logic
signal, V
IH =
1.65. That is, V
PP
must remain above 1.65V to perform in-
system flash modifications.
Raise V
PP
to 12 V
±
5% for faster program and erase
in a production
environment. Applying 12 V
±
5% to V
PP
can only be done for a
maximum of 1000 cycles on the main blocks and 2500 cycles on the
parameter blocks.
V
PP
may be connected to 12 V for a total of 80 hours
maximum. See Section 3.4 for details on V
PP
voltage configurations.
GND
SUPPLY
GROUND:
For all internal circuitry. All ground inputs
must
be
connected.
NC
NO CONNECT:
Pin may be driven or left floating.
2.2
Block Organization
The
asymmetrically-blocked architecture that enables
system integration of code and data within a single
flash
device.
Each
block
independently of the others up to 100,000 times.
For the address locations of each block, see the
memory maps in Appendix E and F.
3 Volt
Advanced+
Boot
Block
is
an
can
be
erased
2.2.1
PARAMETER BLOCKS
The 3 Volt Advanced+ Boot Block flash memory
architecture includes parameter blocks to facilitate
storage of frequently updated small parameters
(i.e., data that would normally be stored in an
EEPROM). Each device contains eight parameter
blocks of 8-Kbytes/4-Kwords (8,192 bytes/4,096
words).
2.2.2
MAIN BLOCKS
After the parameter blocks, the remainder of the
array is divided into equal size (64-Kword/32-
Kword; 65,536 bytes/32,768 words) main blocks for
data or code storage. Each 8-Mbit, 16-Mbit, or
32-Mbit device contains 15, 31, or 63 main blocks,
respectively.
相關PDF資料 |
PDF描述 |
|---|---|
| 28F016SC | Evaluation Kit/Evaluation System for the MAX5954L/MAX5954A |
| 28F032C3 | 3 VOLT ADVANCED+ BOOT BLOCK. 8-. 16-. 32-MBIT FLASH MEMORY FAMILY |
| 28F160F3 | 5V/3.3V or Adjustable, Low-Dropout, Low-IQ, 500mA Linear Regulators |
| 28F800F3 | 3 Volt Fast Boot Block Flash Memory(3 V 8M位快速引導塊閃速存儲器) |
| 28F160F3 | 16MBIT Fast Boot Block Flash Memory(16兆位的快速引導塊閃速存儲器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 28F016S5 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:BYTE-WIDE SMART 5 FlashFile MEMORY FAMILY 4. 8. AND 16 MBIT |
| 28F016SA | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:28F016SA 16-MBIT (1 MBIT X 16, 2 MBIT X 8)FlashFile MEMORY |
| 28F016SA/DD28F032SA | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:INFORMATION |
| 28F016SA-070 | 制造商:undefined 功能描述: |
| 28F016SC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:28F016SC - BYTE-WIDE SmartVoltage FlashFile MEMORY FAMILY 4. 8. AND 16 MBIT |
發布緊急采購，3分鐘左右您將得到回復。