參數資料
型號： 28F016S3
英文描述： Evaluation Kit for the MAX5950/MAX5951
中文描述： 字節寬的SMART 3 FlashFile Memory系列4。 8。及16兆比特
文件頁數： 11/59頁
文件大小： 384K
代理商： 28F016S3
E
3.0
3 VOLT ADVANCED+ BOOT BLOCK
11
PRODUCT PREVIEW
PRINCIPLES OF OPERATION
The 3 Volt Advanced+ Boot Block flash memory
family utilizes a CUI and automated algorithms to
simplify program and erase operations. The CUI
allows for 100% CMOS-evel control inputs and
fixed
power
supplies
programming.
during
erasure
and
The internal WSM completely automates program
and erase operations while the CUI signals the start
of an operation and the status register reports
status. The CUI handles the WE# interface to the
data and address latches, as well as system status
requests during WSM operation.
3.1
Bus Operation
The 3 Volt Advanced+ Boot Block flash memory
devices read, program and erase in-system via the
local CPU or microcontroller. All bus cycles to or
from the flash memory conform to standard
microcontroller bus cycles. Four control pins dictate
the data flow in and out of the flash component:
CE#, OE#, WE# and RP#. These bus operations
are summarized in Table 3.
3.1.1
READ
The flash memory has four read modes available:
read array, read configuration, read status and read
query. These modes are accessible independent of
the V
voltage. The appropriate read mode
command must be issued to the CUI to enter the
corresponding mode. Upon initial device power-up
or after exit from reset, the device automatically
defaults to read array mode.
CE# and OE# must be driven active to obtain data
at the outputs. CE# is the device selection control;
when active it enables the flash memory device.
OE# is the data output control and it drives the
selected memory data onto the I/O bus. For all read
modes, WE# and RP# must be at V
IH
. Figure 9
illustrates a read cycle.
3.1.2
OUTPUT DISABLE
With OE# at a logic-high level (V
), the device
outputs are disabled. Output pins are placed in a
high-mpedance state.
3.1.3
STANDBY
Deselecting the device by bringing CE# to a logic-
high level (V
) places the device in standby mode,
which
substantially
reduces
consumption without any latency for subsequent
read accesses. In standby, outputs are placed in a
high-impedance state independent of OE#. If
deselected during program or erase operation, the
device continues to consume active power until the
program or erase operation is complete.
device
power
Table 3. Bus Operations
(1)
Mode
Note
RP#
CE#
OE#
WE#
DQ
0
–7
DQ
8-15
Read (Array, Status,
Configuration, or Query)
2-4
V
IH
V
IL
V
IL
V
IH
D
OUT
D
OUT
Output Disable
2
V
IH
V
IL
V
IH
V
IH
High Z
High Z
Standby
2
V
IH
V
IH
X
X
High Z
High Z
Reset
2,7
V
IL
X
X
X
High Z
High Z
Write
2,5-7
V
IH
V
IL
V
IH
V
IL
D
IN
D
IN
NOTES:
1.
2.
3.
4.
5.
6.
7.
8-bit devices use only DQ[0:7], 16-bit devices use DQ[0:15]
X must be V
IL
, V
IH
for control pins and addresses.
See DC Characteristicsfor V
PPLK
, V
PP1
, V
PP2
, V
PP3
, voltages.
Manufacturer and device codes may also be accessed in read configuration mode (A
1
–A
20
= 0). See Table 4.
Refer to Table 5 for valid D
IN
during a write operation.
To program or erase the lockable blocks, hold WP# at V
IH
.
RP# must be at GND
±
0.2 V to meet the maximum deep power-down current specified.
相關PDF資料
PDF描述
28F016SC Evaluation Kit/Evaluation System for the MAX5954L/MAX5954A
28F032C3 3 VOLT ADVANCED+ BOOT BLOCK. 8-. 16-. 32-MBIT FLASH MEMORY FAMILY
28F160F3 5V/3.3V or Adjustable, Low-Dropout, Low-IQ, 500mA Linear Regulators
28F800F3 3 Volt Fast Boot Block Flash Memory(3 V 8M位快速引導塊閃速存儲器)
28F160F3 16MBIT Fast Boot Block Flash Memory(16兆位的快速引導塊閃速存儲器)
相關代理商/技術參數
參數描述
28F016S5 制造商:未知廠家 制造商全稱:未知廠家 功能描述:BYTE-WIDE SMART 5 FlashFile MEMORY FAMILY 4. 8. AND 16 MBIT
28F016SA 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:28F016SA 16-MBIT (1 MBIT X 16, 2 MBIT X 8)FlashFile MEMORY
28F016SA/DD28F032SA 制造商:未知廠家 制造商全稱:未知廠家 功能描述:INFORMATION
28F016SA-070 制造商:undefined 功能描述:
28F016SC 制造商:未知廠家 制造商全稱:未知廠家 功能描述:28F016SC - BYTE-WIDE SmartVoltage FlashFile MEMORY FAMILY 4. 8. AND 16 MBIT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*