- 您現在的位置：買賣IC網 > PDF目錄368957 > 28F016S3 Evaluation Kit for the MAX5950/MAX5951 PDF資料下載
參數資料
| 型號： | 28F016S3 |
| 英文描述： | Evaluation Kit for the MAX5950/MAX5951 |
| 中文描述： | 字節寬的SMART 3 FlashFile Memory系列4。 8。及16兆比特 |
| 文件頁數： | 23/59頁 |
| 文件大?。?/td> | 384K |
| 代理商： | 28F016S3 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁
E
3 VOLT ADVANCED+ BOOT BLOCK
23
PRODUCT PREVIEW
V
CC
V
PP
12 V Fast Programming
Complete Write Protection When V
PP
≠
12 V
System Supply
12 V Supply
10 K
V
CC
V
PP
System Supply
12 V Supply
12 V Fast Programming
Full Array Protection Unavailable
V
CC
V
PP
System Supply
Prot#
(Logic Signal)
V
CC
V
PP
System Supply
Low-Voltage Programming Only
Full Array Protection Unavailable
Low-Voltage Programming Only
Logic Control of Complete Device Protection
(Note 1)
0645_06
NOTE:
1.
A resistor can be used if the V
CC
supply can sink adequate current based on resistor value. See AP-657 Designing with
the Advanced+ Boot Block Flash Memory Architecturefor details.
Figure 6. Example Power Supply Configurations
When V
PP
is raised to 12 V, such as in a
manufacturing situations, the device directly applies
the high voltage to achieve faster program and
erase.
Designing for in-system writes to the flash memory
requires special consideration of power supply
traces by the printed circuit board designer.
Adequate power supply traces, and decoupling
capacitors placed adjacent to the component, will
decrease spikes and overshoots.
3.6
Power Consumption
Intel’s flash devices have a tiered approach to
power savings that can significantly reduce overall
system power consumption. The Automatic Power
Savings (APS) feature reduces power consumption
when the device is selected but idle. If the CE# is
deasserted, the flash enters its standby mode,
where current consumption is even lower. The
combination of these features can minimize
memory power consumption, and therefore, overall
system power consumption.
3.6.1
ACTIVE POWER
(Program/Erase/Read)
With CE# at a logic
-
low level and RP# at a logic
-
high level, the device is in the active mode. Refer to
the DC Characteristic tables for I
CC
current values.
Active power is the largest contributor to overall
system power consumption. Minimizing the active
current could have a profound effect on system
power consumption, especially for battery
-
operated
devices.
3.6.2
AUTOMATIC POWER SAVINGS (APS)
Automatic Power Savings provides low
-
power
operation during read mode. After data is read from
the memory array and the address lines are
quiescent, APS circuitry places the device in a
mode where typical current is comparable to I
CCS
.
The flash stays in this static state with outputs valid
until a new location is read.
3.6.3
STANDBY POWER
With CE# at a logic
-
high level (V
IH
) and device in
read mode, the flash memory is in standby mode,
which disables much of the device’s circuitry and
相關PDF資料 |
PDF描述 |
|---|---|
| 28F016SC | Evaluation Kit/Evaluation System for the MAX5954L/MAX5954A |
| 28F032C3 | 3 VOLT ADVANCED+ BOOT BLOCK. 8-. 16-. 32-MBIT FLASH MEMORY FAMILY |
| 28F160F3 | 5V/3.3V or Adjustable, Low-Dropout, Low-IQ, 500mA Linear Regulators |
| 28F800F3 | 3 Volt Fast Boot Block Flash Memory(3 V 8M位快速引導塊閃速存儲器) |
| 28F160F3 | 16MBIT Fast Boot Block Flash Memory(16兆位的快速引導塊閃速存儲器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 28F016S5 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:BYTE-WIDE SMART 5 FlashFile MEMORY FAMILY 4. 8. AND 16 MBIT |
| 28F016SA | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:28F016SA 16-MBIT (1 MBIT X 16, 2 MBIT X 8)FlashFile MEMORY |
| 28F016SA/DD28F032SA | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:INFORMATION |
| 28F016SA-070 | 制造商:undefined 功能描述: |
| 28F016SC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:28F016SC - BYTE-WIDE SmartVoltage FlashFile MEMORY FAMILY 4. 8. AND 16 MBIT |
發布緊急采購，3分鐘左右您將得到回復。