- 您現在的位置：買賣IC網 > PDF目錄371439 > 29F1610A-10 (Macronix International Co., Ltd.) The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each PDF資料下載
參數資料
| 型號： | 29F1610A-10 |
| 廠商： | Macronix International Co., Ltd. |
| 元件分類： | EEPROM |
| 英文描述： | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
| 中文描述： | 該CAT24FC02是一個2 KB的EEPROM的國內256個8位每字舉辦的串行CMOS |
| 文件頁數： | 11/39頁 |
| 文件大?。?/td> | 669K |
| 代理商： | 29F1610A-10 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
11
P/N: PM0506
REV.1.7, JUN. 15, 2001
MX29F1610A
CLEAR STATUS REGISTER
The Eraes fail status bit (DQ5) and Program fail status bit
(DQ4) are set by the write state machine, and can only be
reset by the system software. These bits can indicate
various failure conditions(see Table 6). By allowing the
system software to control the resetting of these bits,
several operations may be performed (such as
cumulatively programming several pages or erasing
multiple blocks in squence). The status register may then
be read to determine if an error occurred during that
programming or erasure series. This adds flexibility to the
way the device may be programmed or erased.
Additionally, once the program(erase) fail bit happens,
the program (erase) operation can not be performed
further. The program(erase) fail bit must be reset by
system software before further page program or sector
(chip) erase are attempted. To clear the status register,
the Clear Status Register command is written to the CIR.
Then, any other command may be issued to the CIR.
Note again that before a read cycle can be initiated, a
Read command must be written to the CIR to specify
whether the read data is to come from the Array, Status
Register or Silicon ID.
READ STATUS REGISTER
The MXIC's16 Mbit flash family contains a status register
which may be read to determine when a program or erase
operation is complete, and whether that operation
completed successfully. The status register may be read
at any time by writing the Read Status command to the
CIR. After writing this command, all subsequent read
operations output data from the status register until
another valid command sequence is written to the CIR.
A Read Array command must be written to the CIR to
return to the Read Array mode.
The status register bits are output on DQ2 - DQ7(table 6)
whether the device is in the byte-wide (x8) or word-wide
(x16) mode for the MX29F1610A. In the word-wide mode
the upper byte, DQ(8:15) is set to 00H during a Read
Status command. In the byte-wide mode, DQ(8:14) are
tri-stated and DQ15/A-1 retains the low order address
function. DQ0-DQ1 is set to 0H in either x8 or x16 mode.
It should be noted that the contents of the status register
are latched on the falling edge of OE or CE whichever
occurs last in the read cycle. This prevents possible bus
errors which might occur if the contents of the status
register change while reading the status register. CE or
OE must be toggled with each subsequent status read, or
the completion of a program or erase operation will not be
evident.
The Status Register is the interface between the
microprocessor and the Write State Machine (WSM).
When the WSM is active, this register will indicate the
status of the WSM, and will also hold the bits indicating
whether or not the WSM was successful in performing the
desired operation. The WSM sets status bits four through
seven and clears bits six and seven, but cannot clear
status bits four and five. If Erase fail or Program fail status
bit is detected, the Status Register is not cleared until the
Clear Status Register command is written. The
MX29F1610A automatically outputs Status Register data
when read after Chip Erase, Sector Erase, Page Program
or Read Status Command write cycle. The internal state
machine is set for reading array data upon device power-
up, or after deep power-down mode.
相關PDF資料 |
PDF描述 |
|---|---|
| 29F1610A-12 | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
| 29F1610A-90 | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
| 29F200C-55 | 2M-BIT [256Kx8/128Kx16] CMOS FLASH MEMORY |
| 29F200C-70 | 2M-BIT [256Kx8/128Kx16] CMOS FLASH MEMORY |
| 29F200C-90 | 2M-BIT [256Kx8/128Kx16] CMOS FLASH MEMORY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 29F1610A-12 | 制造商:MCNIX 制造商全稱:Macronix International 功能描述:16M-BIT [2M x8/1M x16] CMOS SINGLE VOLTAGE FLASH EEPROM |
| 29F1610A-90 | 制造商:MCNIX 制造商全稱:Macronix International 功能描述:16M-BIT [2M x8/1M x16] CMOS SINGLE VOLTAGE FLASH EEPROM |
| 29F200 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:2 Mbit 256Kb x8 or 128Kb x16, Boot Block Single Supply Flash Memory |
| 29F200BB-70EI | 制造商:undefined 功能描述: |
| 29F200BT70SC | 制造商:undefined 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。