- 您現在的位置：買賣IC網 > PDF目錄371439 > 29F400T-90PC (Electronic Theatre Controls, Inc.) 4MEGABIT (512K x 8/ 256K x 16) 5VOLT SECTOR ERASE CMOS FLASH MEMORY PDF資料下載
參數資料
| 型號： | 29F400T-90PC |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | 4MEGABIT (512K x 8/ 256K x 16) 5VOLT SECTOR ERASE CMOS FLASH MEMORY |
| 中文描述： | 4MEGABIT（為512k × 8 / 256K × 16）5VOLT扇區擦除的CMOS閃存 |
| 文件頁數： | 8/38頁 |
| 文件大小： | 240K |
| 代理商： | 29F400T-90PC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
BRIGHT Preliminary BM29F400T/BM29F400B
Microelectronics
Inc.
- 8 -
If the device is deselected during programming or erase, the device will draw active current until the
programming or erase operation is completed. In the standby mode the outputs are in a high
impedance state, independent of the
OE
input.
Output Disable Mode
With the
OE
input at a logic high level (V
IH
), output from the device is disabled. This will cause the
output pins to be in a high impedance state. It is shown in Table 1 that
CE
= V
IL
and
WE
= V
IH
for
Output Disable. This is to differentiate Output Disable mode from Write mode and to prevent
inadvertent writes during Output Disable.
Program and Erase Modes
Device programming and erase are accomplished via the command register. Contents of the register
serve as inputs to the internal state machine. Outputs of the state machine dictate the function of the
device.
The command register itself does not occupy any addressable memory locations. The register is a
latch used to store the commands along with the addresses and data information needed to execute
the command. The command register is written by bringing
WE
to V
IL
, while
CE
is at V
IL
and
OE
is
at V
IH
. Addresses are latched on the falling edge of
WE
or
CE
, whichever happens later, while data
is latched on the rising edge of
WE
or
CE
, whichever happens first. Standard microprocessor write
timings are used. Refer to AC Characteristics for Programming/Erase and their respective Timing
Waveforms for specific timing parameters.
Enable Sector Protect and Verify Sector Protect Modes
The BM29F400 has a hardware Sector Protect mode that disables both Programming and Erase
operation to the protected sector(s). There are total of 11 sectors in this device. The sector protect
feature is enabled using the programming equipment at the user's site. The device is shipped from
the BMI factory with all sectors unprotected.
To verify programming of the protection circuitry, the programming equipment must force V
ID
on the
address pin A9 with
CE
and
OE
at V
IL
and
WE
at V
IH
. As shown in Table 2, scanning the sector
addresses while (A6, A1 and A0) = (0, 1, 0) will produce a 01H code at the device output pins for a
protected sector. In the Verify Sector Protect mode, the device will read 00H for an unprotected
sector. In this mode, the lower order addresses, except for A0, A1 and A6, are don't care. Address
locations with A1 = V
IL
are reserved for Electronic ID manufacturer and device codes. It is also
possible to determine if a sector is protected in-system by writing the Electronic ID command
(described in the Electronic ID command section below.)
Temporary Sector Unprotect Mode
The BM29F400 has a Temporary Sector Unprotect feature that allows the protect feature to be
temporarily suspended to change data in a protected sector in-system. The Temporary Sector
Unprotect mode is activated by setting the
RESET
pin to V
ID
(11.5V - 12.5V).
In this mode, protected sectors can be programmed or erased by selecting the sector addresses.
Once V
ID
is removed from the
RESET
pin, all previously protected sectors will be protected. Refer to
the Temporary Sector Unprotect algorithm and timing waveforms.
相關PDF資料 |
PDF描述 |
|---|---|
| 29F400T-90PI | 4MEGABIT (512K x 8/ 256K x 16) 5VOLT SECTOR ERASE CMOS FLASH MEMORY |
| 29F400T-90TC | 4MEGABIT (512K x 8/ 256K x 16) 5VOLT SECTOR ERASE CMOS FLASH MEMORY |
| 29F400T-90TI | 4MEGABIT (512K x 8/ 256K x 16) 5VOLT SECTOR ERASE CMOS FLASH MEMORY |
| 29F400B-12PC | 4MEGABIT (512K x 8/ 256K x 16) 5VOLT SECTOR ERASE CMOS FLASH MEMORY |
| 29F400C-55 | 4M-BIT [512Kx8/256Kx16] CMOS SINGLE VOLTAGE 5V ONLY BOOT SECTOR FLASH MEMORY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 29F400T-90PI | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:4MEGABIT (512K x 8/ 256K x 16) 5VOLT SECTOR ERASE CMOS FLASH MEMORY |
| 29F400T-90TC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:4MEGABIT (512K x 8/ 256K x 16) 5VOLT SECTOR ERASE CMOS FLASH MEMORY |
| 29F400T-90TI | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:4MEGABIT (512K x 8/ 256K x 16) 5VOLT SECTOR ERASE CMOS FLASH MEMORY |
| 29F516S050B | 制造商:Micro Plastics Inc 功能描述: |
| 29F519G4 | 制造商: 功能描述: 制造商:undefined 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。