參數資料
型號： 6P8B
廠商： NEC Corp.
英文描述： MOS INTEGRATED CIRCUIT 4-BIT SINGLE-CHIP MICROCONTROLLER FOR INFRARED REMOTE CONTROL TRANSMISSION
中文描述： 馬鞍山集成電路4位單片機的紅外遙控傳輸
文件頁數： 34/95頁
文件大?。?/td> 692K
代理商： 6P8B
34
μ
PD6P8, 6P8A, 6P8B
Data Sheet U17848EJ3V0DS
6.2 Standby Mode Setting and Release
The standby mode is set with the HALT #b
3
b
2
b
1
b
0
B instruction for both STOP mode and HALT mode. For the
standby mode to be set, the status flag (F) is required to have been cleared (to 0).
The standby mode is released by the release condition specified with the reset (POC) or the operand of HALT
instruction. If the standby mode is released, the status flag (F) is set (to 1).
Even when the HALT instruction is executed in the state that the status flag (F) has been set (to 1), the standby
mode is not set. If the release condition is not met at this time, the status flag is cleared (to 0). If the release condition
is met, the status flag remains set (to 1).
Even in the case when the release condition has been already met at the point that the HALT instruction is
executed, the standby mode is not set. Here, also, the status flag (F) is set (to 1).
Caution Depending on the status of the status flag (F), the HALT instruction may not be executed. Be
careful about this. For example, when setting HALT mode after checking the key status with
the STTS instruction, the system does not enter HALT mode as long as the status flag (F)
remains set (to 1) and thus sometimes performs an unintended operation. In this case, the
intended operation can be realized by executing the STTS instruction immediately after setting
the timer to clear (to 0) the status flag.
Example
STTS
#03H
;To check the K
I
pin status.
MOV
STTS
T, #0xxH
#05H
(During this time, be sure not to execute an instruction that may set the status flag.)
#05H
;To set HALT mode
;To set the timer
;To clear the status flag
HALT
Table 6-2. Addresses Executed After Standby Mode Release
Release Condition
Address Executed After Release
Reset
Address 0
Release condition shown in Table 5-3
The address following the HALT instruction
…
…
相關PDF資料
PDF描述
6PHR60 FAST RECOVERY SINGLE-PHASE FULL WAVE BRIDGE 6 AMPERES FOR P.C. BOARD AND HEAT SINK MOUNTING 200 NANOSECOND FAST RECOVERY
6PHR FAST RECOVERY SINGLE-PHASE FULL WAVE BRIDGE 6 AMPERES FOR P.C. BOARD AND HEAT SINK MOUNTING 200 NANOSECOND FAST RECOVERY
6PHR05 FAST RECOVERY SINGLE-PHASE FULL WAVE BRIDGE 6 AMPERES FOR P.C. BOARD AND HEAT SINK MOUNTING 200 NANOSECOND FAST RECOVERY
6PHR10 FAST RECOVERY SINGLE-PHASE FULL WAVE BRIDGE 6 AMPERES FOR P.C. BOARD AND HEAT SINK MOUNTING 200 NANOSECOND FAST RECOVERY
6PHR100 FAST RECOVERY SINGLE-PHASE FULL WAVE BRIDGE 6 AMPERES FOR P.C. BOARD AND HEAT SINK MOUNTING 200 NANOSECOND FAST RECOVERY
相關代理商/技術參數
參數描述
6PA1 功能描述:開關配件 Enclose Basic Switch RoHS:否 制造商:C&K Components 類型:Cap 用于:Pushbutton Switches 設計目的:
6PA102 功能描述:開關配件 YOKE ROLLER NYLON BOTH MNT ON FRONT RoHS:否 制造商:C&K Components 類型:Cap 用于:Pushbutton Switches 設計目的:
6PA102-4 制造商:Honeywell Sensing and Control 功能描述:Limit Switch-Sp Part
6PA104 功能描述:開關配件 SWITCH PACKET NYLON RoHS:否 制造商:C&K Components 類型:Cap 用于:Pushbutton Switches 設計目的:
6PA105 功能描述:開關配件 SWITCH PACKET NYLON RoHS:否 制造商:C&K Components 類型:Cap 用于:Pushbutton Switches 設計目的:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*