- 您現在的位置：買賣IC網 > PDF目錄360516 > 7536 Low Quiescent Current LDO, -40C to +125C, 3-SOT-23, T/R PDF資料下載
參數資料
| 型號： | 7536 |
| 英文描述： | Low Quiescent Current LDO, -40C to +125C, 3-SOT-23, T/R |
| 中文描述： | 7536組數據表數據表660K/SEP.05.00 |
| 文件頁數： | 31/46頁 |
| 文件大?。?/td> | 660K |
| 代理商： | 7536 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
7536 Group
MITSUBISHI MICROCOMPUTERS
30
Watchdog Timer
The watchdog timer gives a means for returning to a reset status
when the program fails to run on its normal loop due to a runaway.
The watchdog timer consists of an 8-bit watchdog timer H and an 8-
bit watchdog timer L, being a 16-bit counter.
Standard operation of watchdog timer
The watchdog timer stops when the watchdog timer control register
(address 0039
16
) is not set after reset. Writing an optional value to
the watchdog timer control register (address 0039
16
) causes the
watchdog timer to start to count down. When the watchdog timer H
underflows, an internal reset occurs. Accordingly, it is programmed
that the watchdog timer control register (address 0039
16
) can be set
before an underflow occurs.
When the watchdog timer control register (address 0039
16
) is read,
the values of the high-order 6-bit of the watchdog timer H, STP in-
struction disable bit and watchdog timer H count source selection bit
are read.
Initial value of watchdog timer
By a reset or writing to the watchdog timer control register (address
0039
16
), the watchdog timer H is set to “FF
16
” and the watchdog
timer L is set to “FF
16
”.
Operation of watchdog timer H count source selection bit
A watchdog timer H count source can be selected by bit 7 of the
watchdog timer control register (address 0039
16
). When this bit is
“0”, the count source becomes a watchdog timer L underflow signal.
The detection time is 174.763 ms at f(X
IN
)=6 MHz.
When this bit is “1”, the count source becomes f(X
IN
)/16. In this
case, the detection time is 683
μ
s at f(X
IN
)=6 MHz.
This bit is cleared to “0” after reset.
Operation of STP instruction disable bit
When the watchdog timer is in operation, the STP instruction can be
disabled by bit 6 of the watchdog timer control register (address
0039
16
).
When this bit is “0”, the STP instruction is enabled.
When this bit is “1”, the STP instruction is disabled, and an internal
reset occurs if the STP instruction is executed.
Once this bit is set to “1”, it cannot be changed to “0” by program.
This bit is cleared to “0” after reset.
Fig. 35 Block diagram of watchdog timer
Fig. 36 Structure of watchdog timer control register
Watchdog timer control register(address 0039
16
)
WDTCON
Watchdog timer H (read only for high-order 6-bit)
STP instruction disable bit
0 : STP instruction enabled
1 : STP instruction disabled
Watchdog timer H count source selection bit
0 : Watchdog timer L underflow
1 : f(X
IN
)/16
b7 b0
X
IN
Data bus
“0”
“1”
Watchdog timer H count
source selection bit
1/16
Reset
circuit
STP Instruction Disable Bit
STP Instruction
Watchdog timer H (8)
Write "FF
16
" to the
watchdog timer
control register
Internal reset
RESET
Watchdog timer L (8)
Write "FF
16
" to the
watchdog timer
control register
相關PDF資料 |
PDF描述 |
|---|---|
| 754080 | 250mA CMOS LDO, lsupply 1uA and 2% Vout Accuracy, -40C to +125C, 3-SOT-23, T/R |
| 8525X12 | SCHRAUBE LINSE SCHLITZ M2.5 12MM Inhalt pro Packung: 100 Stk. |
| 8525X16 | SCHRAUBE LINSE SCHLITZ M2.5 16MM Inhalt pro Packung: 100 Stk. |
| 8525X6 | SCHRAUBE LINSE SCHLITZ M2.5 6MM Inhalt pro Packung: 100 Stk. |
| 852X12 | SCHRAUBE LINSE SCHLITZ M2 12MM Inhalt pro Packung: 100 Stk. |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 75360 | 功能描述:BIT MICRO HEX SYST4 9/64" 28MM RoHS:否 類別:工具 >> 螺釘和螺母驅動器 - 刀片和位 系列:系統 4 標準包裝:1 系列:TorqueVario™ 類型:十字槽刀片 尺寸:#2 長度:7.48"（190mm） 特點:絕緣達 10,000V 重量:0.07 磅（31.75g） |
| 75360-0033 | 制造商:MOLEX 功能描述:GBX 5 PAIR DAUGHTERCARD A |
| 753-602 | 制造商:WAGO Innovative Connections 功能描述:24V DC Power Supply |
| 753603 | 制造商:TE CONNECTIVITY 功能描述:BNC CONN AMP 制造商:Yokogawa Electric Corporation 功能描述:POCKET DMM, YOKOGAWA, YOKOGA |
| 753-603 | 制造商:WAGO Innovative Connections 功能描述:Potential Multiplication Module |
發布緊急采購，3分鐘左右您將得到回復。