參數資料
型號： 935086530512
廠商： NXP SEMICONDUCTORS
元件分類： 微控制器/微處理器
英文描述： 8-BIT, 16 MHz, MICROCONTROLLER, PQCC68
封裝： PLASTIC, LCC-68
文件頁數： 33/112頁
文件大?。?/td> 693K
代理商： 935086530512
1996 Jun 27
27
Philips Semiconductors
Product specication
8-bit microcontroller with on-chip CAN
P8xC592
12 SERIAL I/O PORT: SIO0 (UART)
The Serial Port SIO0 is a full duplex (UART) serial I/O port
i.e. it can transmit and receive simultaneously. This Serial
Port is also receive-buffered. It can commence reception
of a second byte before the previously received byte has
been read from the receive register. However, if the first
byte has still not been read by the time reception of the
second byte is complete, one of these (first or second)
bytes will be lost. The SIO0 receive and transmit registers
are both accessed via the S0BUF SFR. Writing to S0BUF
loads the transmit register, and reading S0BUF accesses
to a physically separate receive register. SIO0 can operate
in 4 modes:
Mode 0 Serial data is transmitted and received through
RXD. TXD outputs the shift clock. 8 data bits are
transmitted/received (LSB first). The baud rate is
fixed at 1
12 of the oscillator frequency.
Mode 1 10 bits are transmitted via TXD or received
through RXD: a start bit (0), 8 data bits (LSB first),
and a stop bit (1). On receive, the stop bit is put
into RB8 of the S0CON SFR. The baud rate is
variable.
Mode 2 11 bits are transmitted through TXD or received
through RXD: a start bit (0), 8 data bits (LSB first),
a programmable 9th data bit, and a stop bit (1).
On transmit, the 9th data bit (TB8 in S0CON) can
be assigned the value of 0 or 1. With nominal
software, TB8 can be the parity bit (P in PSW).
During a receive, the 9th data bit is stored in RB8
(S0CON), and the stop bit is ignored. The baud
rate is programmable to either 1
32 or 164 of the
oscillator frequency.
Mode 3 11 bits are transmitted through TXD or received
through RXD: a start bit (0), 8 data bits (LSB first),
a programmable 9th data bit, and a stop bit (1).
Mode 3 is the same as Mode 2 except for the
baud rate which is variable in Mode 3.
In all four modes, transmission is initiated by any
instruction that writes to the S0BUF SFR.
Reception is initiated in Mode 0 when RI = 0 and REN = 1.
In the other three modes, reception is initiated by the
incoming start bit provided that REN = 1.
Modes 2 and 3 are provided for multiprocessor
communications. In these modes, 9 data bits are received
with the 9th bit written to RB8 (S0CON). The 9th bit is
followed by the stop bit. The port can be programmed so
that with receiving the stop bit, the Serial Port interrupt will
be activated if, and only if RB8 = 1.
This feature is enabled by setting bit SM2 in S0CON. This
feature may be used in multiprocessor systems.
For more information about how to use the UART in
combination with the registers S0CON, PCON, IE, SBUF
and the Timer register, refer to the 8051-based
“8-bit Microcontrollers Data Handbook IC20”.
13 SERIAL I/O PORT: SIO1 (CAN)
SIO1 (CAN) provides the CAN (Controller Area Network)
serial-bus data communication interface. SIO1 (CAN)
replaces the SIO1 (I2C) serial interface as provided in the
microcontroller derivative P8xC552.
13.1
On-chip CAN-controller
CAN is the definition of a high performance
communication protocol for serial data communication.
The P8xC592 on-chip CAN-controller is a full
implementation of the CAN 2.0A protocol. With the
P8xC592 powerful local networks can be built, both for
automotive and general industrial environments. This
results in a much reduced wiring harness and enhanced
diagnostic and supervisory capabilities.
13.2
CAN Features
Multi-master architecture
Bus access priority determined by the message
identifier
2032 message identifier (211 standard frame CAN 2.0A)
Guaranteed latency time for high priority messages
Powerful error handling capability
Data length from 0 up to 8 bytes
Multicast and broadcast message facility
Non destructive bit-wise arbitration
Non-return-to-zero (NRZ) coding/decoding with
bit-stuffing
Programmable transfer rate (up to 1 Mbit/s)
Programmable output driver configuration
Suitable for use in a wide range of networks including
the SAE's network classes A, B and C
DMA providing high-speed on-chip data exchange
Bus failure management facility
12AVDD reference voltage.
相關PDF資料
PDF描述
935210470512 8-BIT, OTPROM, 16 MHz, MICROCONTROLLER, PQCC68
935089010512 8-BIT, 16 MHz, MICROCONTROLLER, PQCC68
935085020512 8-BIT, OTPROM, 16 MHz, MICROCONTROLLER, PQCC68
067201.5 Circular Connector; Body Material:Aluminum; Series:PT06; No. of Contacts:2; Connector Shell Size:8; Connecting Termination:Solder; Circular Shell Style:Straight Plug; Circular Contact Gender:Socket; Insert Arrangement:8-2
067201.6 Circular Connector; Body Material:Aluminum; Series:PT06; No. of Contacts:2; Connector Shell Size:8; Connecting Termination:Solder; Circular Shell Style:Straight Plug; Circular Contact Gender:Socket; Insert Arrangement:8-2
相關代理商/技術參數
參數描述
935087-000 制造商:TE Connectivity 功能描述:301A511-51-05/164-0 - Bulk
935087N001 制造商:TE Connectivity 功能描述:301A511-51-05/164-CS7092 制造商:TE Connectivity 功能描述:301A511-51-05/164-CS7092 - Bulk
9350DC-200-0GZZZA 制造商:Siemens 功能描述:
9350DC-200-0ZZZTA 制造商:Siemens 功能描述:
9350DC-200-0ZZZZA 制造商:Siemens 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*