- 您現在的位置：買賣IC網 > PDF目錄36334 > 935242220551 (NXP SEMICONDUCTORS) SPECIALTY CONSUMER CIRCUIT, PQFP208 PDF資料下載
參數資料
| 型號： | 935242220551 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 消費家電 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PQFP208 |
| 封裝： | PLASTIC, SOT-316, SQFP-208 |
| 文件頁數： | 79/148頁 |
| 文件大?。?/td> | 692K |
| 代理商： | 935242220551 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁當前第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁
1998 Apr 09
36
Philips Semiconductors
Product specication
Multimedia bridge, high performance
Scaler and PCI circuit (SPCI)
SAA7146A
7.4.3
COMMAND LIST
An instruction list of an RPS task is built in the system
memory by the device driver. This list is made up of
command sequences; each command being at least one
Dword long. The first Dword of a command consists of the
instruction code (4-bit) and a command specific part
(28 bits). Commands longer than one Dword contain data
in the additional Dwords.
Table 13 Command Dword
7.4.4
THE INSTRUCTION CODE
The instruction code identifies one of the following
commands (see bits 31 to 28 of Tables 14 to 29).
7.4.4.1
PAUSE
The PAUSE command is a one Dword command. This
command contains in the command specific part the
events to wait for; see Tables 14 and 15. The execution of
the RPS task is delayed until the condition addressed via
the events becomes true or a time out occurs.
To control the time a PAUSE command stays in the wait
state, it is possible to set a RPS time out value. This value
specifies after how many PCI clocks and/or V_syncs a
time out will be asserted. When it occurs the RPS_TO bits
in the PSR (see Table 38) is set and if enabled an interrupt
will be generated. However, the RPS will stop this task.
The OAN bit specifies if the condition in bits 25 to 0 is an
AND (OAN set to 0) or if the condition is an OR (OAN set
to 1). If the INV bit is set this command will wait for the
condition to become false.
7.4.4.2
UPLOAD
The UPLOAD command is a one Dword-command. This
command contains in the command specific part the
sections to be uploaded from the shadow RAM to the
working registers, see Tables 16 and 17.
If the UPLOAD command finds a bit of a section set it
uploads the corresponding registers from the shadow
RAM to the working registers. This is done for registers
with changed shadow RAM values only.
D31 to D28
D27 to D0
Instruction code
command specic
7.4.4.3
CHECK-LATE
The CHECK_LATE command is a one Dword-command.
This command contains in the command specific part the
events to check and if necessary to wait for, as shown in
Tables 18 and 19. The execution of the RPS task is
delayed until the condition addressed via the events
becomes true, or a time out occurs and the upload is
performed.
The OAN bit specifies if the condition in bits 25 to 0 is an
AND (OAN set to 0) or if the condition is an OR (OAN set
to 1). If the INV bit is set this command will wait for the
condition to become false.
If the CHECK_LATE command finds that the wait
condition is already true the RPS-LATE is set. Otherwise it
waits for the condition as the PAUSE command. A time out
behaviour such as described for the PAUSE command is
also supplied.
7.4.4.4
CLR_SIGNAL
The CLR_SIGNAL Command clears the selected signals.
This will not affect the real status bits of the SAA7146A.
Only a copy of this bit related to the RPS will be cleared.
It will be set again via a SET_SIGNAL command or when
the real status will be set due to normal processing.
The CLR_SIGNAL format is shown in Tables 20 and 21.
7.4.4.5
NOP
The NOP command consists of one Dword and has the
instruction code 0000. All bits of the command specific
part have to be set to zero. This command is a special
case of the CLR_SIGNAL command!
7.4.4.6
SET_SIGNAL
The SET_SIGNAL command sets the selected signals.
If one of the SAA7146A status related signals is selected
to be set, it will not affect the real status bit of the
SAA7146A. Only a copy of this bit related to the RPS, will
be set. The SET_SIGNAL format is shown in
Tables 22 and 23.
相關PDF資料 |
PDF描述 |
|---|---|
| 935242220557 | SPECIALTY CONSUMER CIRCUIT, PQFP208 |
| 935260698551 | SPECIALTY CONSUMER CIRCUIT, PQFP160 |
| 935260698557 | SPECIALTY CONSUMER CIRCUIT, PQFP160 |
| 935260699551 | SPECIALTY CONSUMER CIRCUIT, PQFP208 |
| 935260699557 | SPECIALTY CONSUMER CIRCUIT, PQFP208 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 935245650125 | 制造商:NXP Semiconductors 功能描述:Inverter 1-Element CMOS 5-Pin TSSOP T/R |
| 935248-90 | 制造商:JANCO 功能描述:935248-90 |
| 9-3525-012 | 制造商:KEYSTONE 功能描述:MODIFIED 3525,VERSION E |
| 935252-5 | 制造商:C-H 功能描述:935252-5 |
| 935257650112 | 制造商:NXP Semiconductors 功能描述:SUB ONLY ICSUBS TO 935257650112 |
發布緊急采購，3分鐘左右您將得到回復。