- 您現在的位置：買賣IC網 > PDF目錄36334 > 935242220551 (NXP SEMICONDUCTORS) SPECIALTY CONSUMER CIRCUIT, PQFP208 PDF資料下載
參數資料
| 型號： | 935242220551 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 消費家電 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PQFP208 |
| 封裝： | PLASTIC, SOT-316, SQFP-208 |
| 文件頁數： | 85/148頁 |
| 文件大?。?/td> | 692K |
| 代理商： | 935242220551 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁當前第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁
1998 Apr 09
41
Philips Semiconductors
Product specication
Multimedia bridge, high performance
Scaler and PCI circuit (SPCI)
SAA7146A
7.4.4.10
LDREG and STREG
The Load Register (LDREG) command has a variable
Dword count specified by the Block_length. It is at least
two Dwords long and at maximum 256 Dwords.
The LDREG command interprets the following Dwords as
data and writes it to the registers beginning at the specified
register address (D6 to D0).
The Store Register (STREG) command is a two Dword
command. It transfers the contents of the addressed
(D6 to D0) SAA7146A register into PCI memory that is
addressed by interpreting the contents of the next data
Dword as the 32-bit target base address.
To perform STREG by two different tasks, a kind of
arbitration with two semaphore signals is necessary.
The Block_length entry defines the number of data
Dwords to be processed by these commands. This
enables the access to multiple registers on following
addresses within a single RPS command. The value
specified must be at least one. If more than one Dword is
accessed the register address is incremented each cycle.
A value of zero is reserved and the command will be
interpreted as NOP.
The register address defines the target register address in
Dwords. If this address points to a non-existent register the
RPS_RE (read error) bit for the actual task will be set and
if enabled an interrupt will be generated. The command will
be ignored and the execution of RPS continues.
All reserved bits should be written as zeros and should be
ignored during read cycles.
Table 30 LDREG command format
Table 31 STREG command format
D31 to D28
D27 to D16
D15 to D8
D7
D6 to D0
1001
reserved
Block_length
reserved
register address
(register offset divided-by-4)
D31 to D28
D27 to D16
D15 to D8
D7
D6 to D0
1010
reserved
Block_length
reserved
register address
(register offset divided-by-4)
Fig.7 Possible solution employing two semaphore signals to perform STREG commands with two tasks.
handbook, halfpage
MHB048
TASK0
SET SIG3
. . .
SET SIG3
CLR SIG3
JUMP IF SIG2 = 0 TO
STREG
ADDRESS
SET SIG3
. . .
TASK1
SET SIG2
. . .
CLR SIG2
WAIT ON SIG3
STREG
ADDRESS
SET SIG2
. . .
相關PDF資料 |
PDF描述 |
|---|---|
| 935242220557 | SPECIALTY CONSUMER CIRCUIT, PQFP208 |
| 935260698551 | SPECIALTY CONSUMER CIRCUIT, PQFP160 |
| 935260698557 | SPECIALTY CONSUMER CIRCUIT, PQFP160 |
| 935260699551 | SPECIALTY CONSUMER CIRCUIT, PQFP208 |
| 935260699557 | SPECIALTY CONSUMER CIRCUIT, PQFP208 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 935245650125 | 制造商:NXP Semiconductors 功能描述:Inverter 1-Element CMOS 5-Pin TSSOP T/R |
| 935248-90 | 制造商:JANCO 功能描述:935248-90 |
| 9-3525-012 | 制造商:KEYSTONE 功能描述:MODIFIED 3525,VERSION E |
| 935252-5 | 制造商:C-H 功能描述:935252-5 |
| 935257650112 | 制造商:NXP Semiconductors 功能描述:SUB ONLY ICSUBS TO 935257650112 |
發布緊急采購，3分鐘左右您將得到回復。