參數資料
型號： 935260017557
廠商： NXP SEMICONDUCTORS
元件分類： 消費家電
英文描述： SPECIALTY CONSUMER CIRCUIT, PQFP64
封裝： PLASTIC, SOT-314, LQFP-64
文件頁數： 64/75頁
文件大?。?/td> 479K
代理商： 935260017557
1998 May 15
67
Philips Semiconductors
Product specication
Enhanced Video Input Processor (EVIP)
SAA7111A
21 SOLDERING
21.1
Introduction
There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-hole and surface mounted components are mixed
on one printed-circuit board. However, wave soldering is
not always suitable for surface mounted ICs, or for
printed-circuits with high population densities. In these
situations reflow soldering is often used.
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our
“IC Package Databook” (order code 9398 652 90011).
21.2
Reow soldering
Reflow soldering techniques are suitable for all LQFP and
QFP packages.
The choice of heating method may be influenced by larger
plastic QFP packages (44 leads, or more). If infrared or
vapour phase heating is used and the large packages are
not absolutely dry (less than 0.1% moisture content by
weight), vaporization of the small amount of moisture in
them can cause cracking of the plastic body. For more
information, refer to the Drypack chapter in our
“Quality
Reference Handbook” (order code 9397 750 00192).
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Several methods exist for reflowing; for example,
infrared/convection heating in a conveyor type oven.
Throughput times (preheating, soldering and cooling) vary
between 50 and 300 seconds depending on heating
method. Typical reflow peak temperatures range from
215 to 250
°C.
21.3
Wave soldering
Wave soldering is not recommended for LQFP and QFP
packages. This is because of the likelihood of solder
bridging due to closely-spaced leads and the possibility of
incomplete solder penetration in multi-lead devices.
CAUTION
Wave soldering is NOT applicable for all LQFP and
QFP packages with a pitch (e) equal or less than
0.5 mm.
If wave soldering cannot be avoided, for LQFP and
QFP packages with a pitch (e) larger than 0.5 mm, the
following conditions must be observed:
A double-wave (a turbulent wave with high upward
pressure followed by a smooth laminar wave)
soldering technique should be used.
The footprint must be at an angle of 45° to the board
direction and must incorporate solder thieves
downstream and at the side corners.
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Maximum permissible solder temperature is 260
°C, and
maximum duration of package immersion in solder is
10 seconds, if cooled to less than 150
°C within
6 seconds. Typical dwell time is 4 seconds at 250
°C.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
21.4
Repairing soldered joints
Fix the component by first soldering two diagonally-
opposite end leads. Use only a low voltage soldering iron
(less than 24 V) applied to the flat part of the lead. Contact
time must be limited to 10 seconds at up to 300
°C. When
using a dedicated tool, all other leads can be soldered in
one operation within 2 to 5 seconds between
270 and 320
°C.
相關PDF資料
PDF描述
935260018551 SPECIALTY CONSUMER CIRCUIT, PQFP64
935260018557 SPECIALTY CONSUMER CIRCUIT, PQFP64
935263652557 SPECIALTY CONSUMER CIRCUIT, PQFP64
935233400112 SPECIALTY CONSUMER CIRCUIT, PDIP24
935233410112 SPECIALTY CONSUMER CIRCUIT, PDSO24
相關代理商/技術參數
參數描述
935260093112 制造商:NXP Semiconductors 功能描述:IC AVIC ADV BASESTATION 14SOIC
935261069122 制造商:NXP Semiconductors 功能描述:IC SECURITY TRANSPONDER PLLMC
935262025112 制造商:NXP Semiconductors 功能描述:SUB ONLY IC
935262217118 制造商:NXP Semiconductors 功能描述:Real Time Clock Serial 8-Pin SO T/R
935264217557 制造商:NXP Semiconductors 功能描述:SUB ONLY IC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*