參數資料
型號: 935287058118
廠商: NXP SEMICONDUCTORS
元件分類: 顯示驅動器
英文描述: LED DISPLAY DRIVER, PQCC28
封裝: 6 X 6 MM, 0.85 MM HIGHT, PLASTIC, MO-220, SOT788-1, HVQFN-28
文件頁數: 29/54頁
文件大?。?/td> 410K
代理商: 935287058118
PCA9685_2
NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 02 — 16 July 2009
35 of 50
NXP Semiconductors
PCA9685
16-channel, 12-bit PWM Fm+ I2C-bus LED controller
Question 1: What kind of edge rate control is there on the outputs?
The typical edge rates depend on the output conguration, supply voltage, and the
applied load. The outputs can be congured as either open-drain NMOS or totem pole
outputs. If the customer is using the part to directly drive LEDs, they should be using it
in an open-drain NMOS, if they are concerned about the maximum ISS and ground
bounce. The edge rate control was designed primarily to slow down the turn-on of the
output device; it turns off rather quickly (~1.5 ns). In simulation, the typical turn-on
time for the open-drain NMOS was ~14 ns (VDD = 3.6 V; CL = 50 pF; RPU = 500 ).
Question 2: Is ground bounce possible?
Ground bounce is a possibility, especially if all 16 outputs are changed at full current
(25 mA each). There is a fair amount of decoupling capacitance on chip (~50 pF),
which is intended to suppress some of the ground bounce. The customer will need to
determine if additional decoupling capacitance externally placed as close as
physically possible to the device is required.
Question 3: Can I really sink 400 mA through the single ground pin on the package and
will this cause any ground bounce problem due to the PWM of the LEDs?
Yes, you can sink 400 mA through a single ground pin on the package. Although the
package only has one ground pin, there are two ground pads on the die itself
connected to this one pin. Although some ground bounce is likely, it will not disrupt the
operation of the part and would be reduced by the external decoupling capacitance.
Question 4: I can’t turn the LEDs on or off, but their registers are set properly. Why?
Check the MODE1 register SLEEP (bit 4) setting. The bit needs to be 0 in order to
enable the clocking. If both clock sources (internal osc and EXTCLK) are turned OFF
(bit 4 = 1), the LEDs cannot be dimmed or blinked.
Question 5: I’m using LEDs with integrated Zener diodes and the IC is getting very hot.
Why?
The IC outputs can be set to either open-drain or push-pull and default to push-pull
outputs. In this application with the Zener diodes, they need to be set to open-drain
since in the push-pull architecture there is a low resistance path to GND through the
Zener and this is causing the IC to overheat.
相關PDF資料
PDF描述
935289802118 LED DISPLAY DRIVER, PDSO28
935288883112 DATACOM, INTERFACE CIRCUIT, PDSO8
935288883115 DATACOM, INTERFACE CIRCUIT, PDSO8
935288883118 DATACOM, INTERFACE CIRCUIT, PDSO8
935085330112 DATACOM, INTERFACE CIRCUIT, PDSO8
相關代理商/技術參數
參數描述
9352-879-67118 制造商:NXP Semiconductors 功能描述:DATACOM, INTERFACE CIRCUIT, PDSO8
935288287551 制造商:NXP Semiconductors 功能描述:- Trays
935288287557 制造商:NXP Semiconductors 功能描述:- Trays
935288465027 制造商:NXP Semiconductors 功能描述:IC SMARTCARD RTC OSC COUNTER
935288948115 制造商:NXP Semiconductors 功能描述:IC ANALOG SWITCH SP3T 10XQFN