- 您現在的位置：買賣IC網 > PDF目錄294746 > 94SA108X0016HBP (Texas Instruments, Inc.) 60-A, 3.3/5-V INPUT, NONISOLATED WIDE-OUTPUT ADJUST POWER MODULE PDF資料下載
參數資料
| 型號： | 94SA108X0016HBP |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | 60-A, 3.3/5-V INPUT, NONISOLATED WIDE-OUTPUT ADJUST POWER MODULE |
| 中文描述： | 60甲，3.3/5-V輸入，非隔離寬輸出調節電源模塊 |
| 文件頁數： | 20/24頁 |
| 文件大?。?/td> | 947K |
| 代理商： | 94SA108X0016HBP |
www.ti.com
DEVICE INFORMATION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
PTHXX040W
(Top View)
16
PTH04040W
SLTS238A – SEPTEMBER 2005 – REVISED FEBRUARY 2006
TERMINAL FUNCTIONS
TERMINAL
DESCRIPTION
NAME
NO.
1, 3, 5, 10, 13, This is the common ground connection for the VI and VO power connections. It is also the 0 Vdc
GND
16
reference for the control inputs.
VI
2, 4, 6
The positive input voltage power node to the module, which is referenced to common GND.
VO
9, 12, 15
The regulated positive power output with respect to the GND node.
The Inhibit pin is an open-collector/drain negative logic input that is referenced to GND. Applying a
lowlevel ground signal to this input disables the module’s output and turns off the output voltage. When
Inhibit(1)
7
the Inhibit control is active, the input current drawn by the regulator is significantly reduced. If the Inhibit
pin is left open-circuit, the module produces an output whenever a valid input source is applied. Do not
place an external pull-up on this pin.
A 1%, 0.05-W resistor must be connected between this pin and GND to set the output voltage higher
than the minimum value. The set-point range for the output voltage is from 0.8 V to 2.5 V. The resistor
required for a given output voltage may be calculated from the following formula. If left open circuit, the
VO Adjust
17
module output defaults to its lowest output voltage value. For further information on the adjustment
and/or trimming of the output voltage, see the related Application Information section. Note: The
specification table gives the preferred resistor values for a number of standard output voltages.
The sense inputs allow the regulation circuit to compensate for voltage drop between the module and
+Sense
11
the load. For optimal voltage accuracy, +Sense should be connected to VO. If it is left open, a low-value
internal resistor ensures that the output remains in regulation.
For optimal voltage accuracy, –Sense should be connected to the ground return at the load. If it is left
–Sense
14
open, a low-value internal resistor ensures that the output remains in regulation.
Connecting a resistor from this pin to signal ground allows the on threshold of the input undervoltage
lockout (UVLO) to be adjusted higher than the default value. The hysterisis can also be independenly
UVLO Prog
8
reduced by connecting a second resistor from this pin to VI. For further information, see the Application
Information section.
This is an analog control input that allows the output voltage to follow another voltage during power up
and power down sequences. The pin is active from 0 V, up to the nominal set-point voltage. Within this
range, the module output follows the voltage at the Track pin on a volt-for-volt basis. When the control
Track
18
voltage is raised above this range, the module regulates at its nominal output voltage. If unused, this
input should be connected to VI for a faster power up. For further information, see the related
Application Information section.
When this input is asserted to GND, the output voltage is decreased by 5% from the nominal. The input
requires an open-collector (open-drain) interface. It is not TTL compatible. A lower percent change can
Margin Down(1)
20
be accommodated with a series resistor. For further information, see the related Application Information
section.
When this input is asserted to GND, the output voltage is increased by 5%. The input requires an open
Margin Up(1)
19
collector (open-drain) interface. It is not TTL compatible. The percent change can be reduced with a
series resistor. For further information, see the related Application Information section.
(1)
Denotes negative logic: Open = Normal operation; Ground = Function active
5
Submit Documentation Feedback
相關PDF資料 |
PDF描述 |
|---|---|
| 950-430A-B2B | TWO PART BOARD CONNECTOR |
| 950-430A-B2C | TWO PART BOARD CONNECTOR |
| 950-430A-B2D | TWO PART BOARD CONNECTOR |
| 950-430A-B2E | TWO PART BOARD CONNECTOR |
| 950-430C-B2B | TWO PART BOARD CONNECTOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 94SA156X0020CBP | 功能描述:鋁有機聚合物電容器 15uF 20V 20% RoHS:否 制造商:Panasonic Electronic Components 電容:470 uF 容差:20 % 電壓額定值:2.5 V ESR:4.5 mOhms 工作溫度范圍:- 40 C to + 105 C 端接類型:SMD/SMT 外殼直徑: 外殼長度:7.3 mm 外殼寬度:4.3 mm 外殼高度:1.9 mm 封裝:Reel |
| 94SA157X0016FA1 | 功能描述:鋁有機聚合物電容器 150UF 16V 20% RoHS:否 制造商:Panasonic Electronic Components 電容:470 uF 容差:20 % 電壓額定值:2.5 V ESR:4.5 mOhms 工作溫度范圍:- 40 C to + 105 C 端接類型:SMD/SMT 外殼直徑: 外殼長度:7.3 mm 外殼寬度:4.3 mm 外殼高度:1.9 mm 封裝:Reel |
| 94SA157X0016FBP | 功能描述:鋁有機聚合物電容器 150uF 16V 20% RoHS:否 制造商:Panasonic Electronic Components 電容:470 uF 容差:20 % 電壓額定值:2.5 V ESR:4.5 mOhms 工作溫度范圍:- 40 C to + 105 C 端接類型:SMD/SMT 外殼直徑: 外殼長度:7.3 mm 外殼寬度:4.3 mm 外殼高度:1.9 mm 封裝:Reel |
| 94SA157X0016FT1 | 功能描述:鋁有機聚合物電容器 150UF 16V 20% RoHS:否 制造商:Panasonic Electronic Components 電容:470 uF 容差:20 % 電壓額定值:2.5 V ESR:4.5 mOhms 工作溫度范圍:- 40 C to + 105 C 端接類型:SMD/SMT 外殼直徑: 外殼長度:7.3 mm 外殼寬度:4.3 mm 外殼高度:1.9 mm 封裝:Reel |
| 94SA157X06R3EBP | 功能描述:鋁有機聚合物電容器 150uF 6.3V 20% RoHS:否 制造商:Panasonic Electronic Components 電容:470 uF 容差:20 % 電壓額定值:2.5 V ESR:4.5 mOhms 工作溫度范圍:- 40 C to + 105 C 端接類型:SMD/SMT 外殼直徑: 外殼長度:7.3 mm 外殼寬度:4.3 mm 外殼高度:1.9 mm 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。