- 您現在的位置：買賣IC網 > PDF目錄67355 > A1351KKTTN-T MAGNETIC FIELD SENSOR-HALL EFFECT, 0.20-4.80V, RECTANGULAR, THROUGH HOLE MOUNT PDF資料下載
參數資料
| 型號： | A1351KKTTN-T |
| 元件分類： | 磁阻傳感器 |
| 英文描述： | MAGNETIC FIELD SENSOR-HALL EFFECT, 0.20-4.80V, RECTANGULAR, THROUGH HOLE MOUNT |
| 封裝： | LEAD FREE, PLASTIC, SIP-4 |
| 文件頁數： | 10/23頁 |
| 文件大?。?/td> | 654K |
| 代理商： | A1351KKTTN-T |
A1351
High Precision Linear Hall Effect Sensor IC
with a Push/Pull, Pulse Width Modulated Output
18
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
Try Mode
Try mode allows a single programmable parameter to be tested
without permanently setting its value. (Note that multiple param-
eters cannot be tested simultaneously with the A1351 device.)
Try mode is a required step of parameter blowing. (See the Blow
Mode section for additional information.) After powering the
VCC supply, select the desired parameter register and address its
bit field. When addressing the bit field, each VPM pulse incre-
ments the value of the parameter register, up to the maximum
possible code (see the Programming Logic table). The addressed
parameter value remains stored in the device even after the
programming drive voltage is removed from the PWMOUT pin,
allowing the value to be measured. Note that for accurate pro-
gramming, the blow capacitor, CBLOW, should be replaced with
the application load capacitance, CL, during output voltage mea-
surement. It is not possible to decrement the value of the register
without resetting the parameter bit field. To reset the bit field, and
thus the value of the programmable parameter, cycle the supply
(VCC) voltage.
Blow Mode
After the required value of the programmable parameter is found
using Try mode, its corresponding code should be blown to make
its value permanent. To do this, select the required parameter
register, and address and blow each required bit separately (as
described in the Fuse Blowing section). The supply must be
cycled between blowing each bit of a given code. After a bit is
blown, cycling the supply will not reset its value.
Lock Mode
To lock the device, address the LOCK bit and apply a blow pulse
with CBLOW in place. The LOCK bit is located in register 5, code
512. After locking the device, no future programming of any
parameter is possible.
Programming Modes
相關PDF資料 |
PDF描述 |
|---|---|
| A1354KKTTN-T | MAGNETIC FIELD SENSOR-HALL EFFECT, RECTANGULAR, THROUGH HOLE MOUNT |
| A1382ELHLT-T | MAGNETIC FIELD SENSOR-HALL EFFECT, 4.35-4.65V, RECTANGULAR, SURFACE MOUNT |
| A1381LLHLT-T | MAGNETIC FIELD SENSOR-HALL EFFECT, 4.35-4.65V, RECTANGULAR, SURFACE MOUNT |
| A1384LUA-T | MAGNETIC FIELD SENSOR-HALL EFFECT, 4.35-4.65V, RECTANGULAR, THROUGH HOLE MOUNT |
| A1383EUA-T | MAGNETIC FIELD SENSOR-HALL EFFECT, 4.35-4.65V, RECTANGULAR, THROUGH HOLE MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A1351LKTTN-T | 功能描述:IC SENSOR HALL EFFECT 4-SIP RoHS:是 類別:傳感器，轉換器 >> 磁性 - 霍爾效應，數字式開關，線性，羅盤 (IC) 系列:- 標準包裝:1 系列:- 傳感范圍:20mT ~ 80mT 類型:旋轉 電源電壓:4.5 V ~ 5.5 V 電流 - 電源:15mA 電流 - 輸出（最大）:- 輸出類型:數字式，PWM，8.5 位串行 特點:可編程 工作溫度:-40°C ~ 150°C 封裝/外殼:20-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:20-SSOP 包裝:Digi-Reel® 其它名稱:AS5132-HSST-500DKR |
| A1352-035 | 制造商:AVX Corporation 功能描述: |
| A1352-037 | 制造商:AVX Corporation 功能描述: |
| A13532-43N | 制造商:Harris Corporation 功能描述: |
| A1354 | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:High Precision 2-Wire Linear Hall Effect Sensor IC with Pulse Width Modulated Output |
發布緊急采購，3分鐘左右您將得到回復。