參數資料
型號： A1351KKTTN-T
元件分類： 磁阻傳感器
英文描述： MAGNETIC FIELD SENSOR-HALL EFFECT, 0.20-4.80V, RECTANGULAR, THROUGH HOLE MOUNT
封裝： LEAD FREE, PLASTIC, SIP-4
文件頁數： 11/23頁
文件大?。?/td> 654K
代理商： A1351KKTTN-T
A1351
High Precision Linear Hall Effect Sensor IC
with a Push/Pull, Pulse Width Modulated Output
19
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
Programming State Machine
Initial State
After system power-up, the programming logic is reset to a
known state. This is referred to as the Initial state. All the bit field
locations that have intact fuses are set to logic 0. While in the
Initial state, any VPM pulses on the PWMOUT pin are ignored.
To enter the Parameter Selection state, apply a single VPH pulse
on the PWMOUT pin.
Parameter Selection State
This state allows the selection of the parameter register con-
taining the bit fields to be programmed. To select a parameter
register, increment through the keys by sending VPM pulses on
the PWMOUT pin. Register keys select among the following
programming parameters:
1 pulse – Sens / Coarse D(Q)
2 pulses – D(Q)
3 pulses – PWM Frequency / Calibration Test Mode
5 pulses – LOCK
Bit Field Addressing State
To enter the Bit Field Addressing state, apply one VPH pulse on
the PWMOUT pin. This state allows the selection of the individ-
ual bit fields to be programmed in the selected parameter register
(see the Programming Logic table). To leave this state, either
cycle device power or blow the fuses for the selected code.
Note: Merely addressing the bit field does not permanently set
the value of the selected programming parameter; fuses must be
blown to do so.
Fuse Blowing State
To blow an addressed bit field, apply a VPH pulse on the PWM-
OUT pin. Power to the device should then be cycled before
additional programming is attempted.
Note: Each bit representing a decimal code must be blown indi-
vidually (see the Fuse Blowing section).
Power-up
Initial
Parameter Selection
Bit Field Addressing
Sens/
Coarse
D(Q)
(Fine)
VPH
VPM
VPH
VPM
[Key sequence]
[Code sequence]
VPM
1
2
Null
Lock
VPM
fPWM/
Calibration
Test Mode
2n – 1
n= bits in
register
Fuse Blowing
User Power-down
Required
VPM = VP(LOW) → VP(MID) → VP(LOW)
VPH = VP(LOW) → VP(HIGH) → VP(LOW)
相關PDF資料
PDF描述
A1354KKTTN-T MAGNETIC FIELD SENSOR-HALL EFFECT, RECTANGULAR, THROUGH HOLE MOUNT
A1382ELHLT-T MAGNETIC FIELD SENSOR-HALL EFFECT, 4.35-4.65V, RECTANGULAR, SURFACE MOUNT
A1381LLHLT-T MAGNETIC FIELD SENSOR-HALL EFFECT, 4.35-4.65V, RECTANGULAR, SURFACE MOUNT
A1384LUA-T MAGNETIC FIELD SENSOR-HALL EFFECT, 4.35-4.65V, RECTANGULAR, THROUGH HOLE MOUNT
A1383EUA-T MAGNETIC FIELD SENSOR-HALL EFFECT, 4.35-4.65V, RECTANGULAR, THROUGH HOLE MOUNT
相關代理商/技術參數
參數描述
A1351LKTTN-T 功能描述:IC SENSOR HALL EFFECT 4-SIP RoHS:是 類別:傳感器，轉換器 >> 磁性 - 霍爾效應，數字式開關，線性，羅盤 (IC) 系列:- 標準包裝:1 系列:- 傳感范圍:20mT ~ 80mT 類型:旋轉 電源電壓:4.5 V ~ 5.5 V 電流 - 電源:15mA 電流 - 輸出（最大）:- 輸出類型:數字式，PWM，8.5 位串行 特點:可編程 工作溫度:-40°C ~ 150°C 封裝/外殼:20-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:20-SSOP 包裝:Digi-Reel® 其它名稱:AS5132-HSST-500DKR
A1352-035 制造商:AVX Corporation 功能描述:
A1352-037 制造商:AVX Corporation 功能描述:
A13532-43N 制造商:Harris Corporation 功能描述:
A1354 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:High Precision 2-Wire Linear Hall Effect Sensor IC with Pulse Width Modulated Output
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*