參數資料
型號: A1351KKTTN-T
元件分類: 磁阻傳感器
英文描述: MAGNETIC FIELD SENSOR-HALL EFFECT, 0.20-4.80V, RECTANGULAR, THROUGH HOLE MOUNT
封裝: LEAD FREE, PLASTIC, SIP-4
文件頁數: 14/23頁
文件大?。?/td> 654K
代理商: A1351KKTTN-T
A1351
High Precision Linear Hall Effect Sensor IC
with a Push/Pull, Pulse Width Modulated Output
21
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
To construct a current sensor using the A1351, first consider a
current carrying wire that we want to observe. As dictated by
Ampere’s Law, a magnetic field is produced around the wire
that is proportional to the amount of current flowing through
the wire. By passing this wire through a soft magnetic core, the
magnetic flux produced by the wire can be concentrated and
directed through a gap in the core. The magnetic flux density can
be measured by inserting the A1351 SIP into the gap in the core.
As a result, the output of the A1351 device will be proportional
to the amount of current flowing through the wire.
The example feedthrough current sensing setup shown below
(figure 7) has a core made of “mu metal” that is 2 mm thick
and 4 mm wide. The inner radius of the core is 14.5 mm and
the outer radius is 18.5 mm. The wire going through the center
of the core has a radius of 9 mm. Using this setup with a gap of
1.7 mm, a field strength results that is on the order of 7 G /A at
the Hall element in the A1351.
The recommended core material for construction of the concen-
trator depends on the specific application. If high flux saturation
is desired, then an alloy such as HyPerm49 is recommended.
For lower-current level sensing applications, a material such as
HyMu80 may be desired. (HyMu80 has lower magnetic flux
saturation than HyPerm49, therefore more HyMu80 mate-
rial is required to carry the same amount of flux compared
to Hyperm49.) If frequency response is a concern, then eddy
currents can be reduced by either laminating the HyPerm49 or
HyMu80 alloys, or by using a ferrite core.
Constructing a Current Sensor Using the A1351
18 mm
4 mm
2 mm
37 mm
Application-specific housing
Ring concentrator
Current-conducting wire
A136x
Center Hall element in gap
1.7 mm
Figure 7. The example current sensor setup used to generate the data in this section was
constructed with a split-ring concentrator and an A1351 device. A copper wire was fed
through the concentrator, and the A1351 placed in its gap. This approximates a typical
ammeter application on a thick wire, such as shown in the left view. Note that such
applications usually have a protective housing, which should be taken into consideration
when designing the nal application. The housing is beyond the scope of this example.
相關PDF資料
PDF描述
A1354KKTTN-T MAGNETIC FIELD SENSOR-HALL EFFECT, RECTANGULAR, THROUGH HOLE MOUNT
A1382ELHLT-T MAGNETIC FIELD SENSOR-HALL EFFECT, 4.35-4.65V, RECTANGULAR, SURFACE MOUNT
A1381LLHLT-T MAGNETIC FIELD SENSOR-HALL EFFECT, 4.35-4.65V, RECTANGULAR, SURFACE MOUNT
A1384LUA-T MAGNETIC FIELD SENSOR-HALL EFFECT, 4.35-4.65V, RECTANGULAR, THROUGH HOLE MOUNT
A1383EUA-T MAGNETIC FIELD SENSOR-HALL EFFECT, 4.35-4.65V, RECTANGULAR, THROUGH HOLE MOUNT
相關代理商/技術參數
參數描述
A1351LKTTN-T 功能描述:IC SENSOR HALL EFFECT 4-SIP RoHS:是 類別:傳感器,轉換器 >> 磁性 - 霍爾效應,數字式開關,線性,羅盤 (IC) 系列:- 標準包裝:1 系列:- 傳感范圍:20mT ~ 80mT 類型:旋轉 電源電壓:4.5 V ~ 5.5 V 電流 - 電源:15mA 電流 - 輸出(最大):- 輸出類型:數字式,PWM,8.5 位串行 特點:可編程 工作溫度:-40°C ~ 150°C 封裝/外殼:20-SSOP(0.209",5.30mm 寬) 供應商設備封裝:20-SSOP 包裝:Digi-Reel® 其它名稱:AS5132-HSST-500DKR
A1352-035 制造商:AVX Corporation 功能描述:
A1352-037 制造商:AVX Corporation 功能描述:
A13532-43N 制造商:Harris Corporation 功能描述:
A1354 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:High Precision 2-Wire Linear Hall Effect Sensor IC with Pulse Width Modulated Output