- 您現在的位置：買賣IC網 > PDF目錄164964 > A1361LKTTN-T MAGNETIC FIELD SENSOR-HALL EFFECT, 4.65-4.80V, RECTANGULAR, THROUGH HOLE MOUNT PDF資料下載
參數資料
| 型號： | A1361LKTTN-T |
| 元件分類： | 磁阻傳感器 |
| 英文描述： | MAGNETIC FIELD SENSOR-HALL EFFECT, 4.65-4.80V, RECTANGULAR, THROUGH HOLE MOUNT |
| 封裝： | LEAD FREE, PLASTIC, SIP-4 |
| 文件頁數： | 10/25頁 |
| 文件大小： | 615K |
| 代理商： | A1361LKTTN-T |
A1360, A1361,
and A1362
Hold Mode
Hold mode allows multiple programmable parameters to be
tested simultaneously without permanently setting any values.
With the 136x programming logic, only two parameters located
in different zones can be addressed together. For example, only
the sensitivity and fine quiescent voltage offset parameters can be
temporarily set and tested simultaneously without permanently
setting their values. For unidirectional devices, the unidirectional
bit must be permanently blown before using the Hold Mode to
temporarily set and test the sensitivity and fine quiescent voltage
offset.
Powering the VCC supply automatically causes the device to
enter the first zone. Applying a high pulse, mid pulse, high pulse
sequence selects the Sensitivity register. The sensitivity can be set
to the desired value by applying the appropriate code pulses.
The next high-level pulse transitions the programming logic into
the second zone. Applying one mid level pulse causes the logic
to enter the Fine Quiescent Voltage Output register, and another
high-level pulse causes the logic to enter the Fine Quiescent
Voltage Output bit field. The fine quiescent voltage output can
be set to the desired level by applying the appropriate number of
mid-level pulses to the VOUT pin. (See figure 4.)
The addressed parameter values will be stored in the device logic
even after the programming drive voltage is removed from the
VOUT pin, allowing the output to be measured at any time dur-
ing the programming process.
Figure 4. Hold sequence for testing Sens and VOUT(Q) parameters
together.
After addressing and measuring the device output, cycle the sup-
ply to reset all of the register values. Registers can be addressed
and re-addressed an indefinite number of times. Once the final
desired code is found for each register, cycle the supply and blow
the bit field using Blow mode.
Note: For accurate time measurements, the blow capacitor,
CBLOW, should be removed during output voltage measurement.
Also note that both the Sensitivity and Fine Quiescent Voltage
Output registers should not be blown simultaneously. See the
Blow Mode section for additional information.
Try Mode
Try mode allows a single programmable parameter to be tested
without permanently setting its value. Try mode is a required step
of parameter blowing. (See the Blow Mode section for additional
information.) To select a parameter register in the first zone,
power the supply and enter the appropriate key-code pulse com-
bination (see figure 5). To select a parameter register in the sec-
ond zone, power the supply and apply two high voltage pulses,
followed by the appropriate key-code pulse combination (see
Figure 6). When addressing the bit field, each VPM pulse incre-
ments the value of the parameter register, up to the maximum
possible code (see the Programming Logic table). The addressed
parameter value is stored in the device even after the program-
ming drive voltage is removed from the VOUT pin, allowing its
value to be measured.
Note: For accurate time measurements, the blow capacitor,
CBLOW, should be removed during output voltage measurement.
To reset the bit field, and thus the value of the programmable
parameter, cycle the VCC supply voltage.
Figure 5. Pulses to enter Try mode, zone 1. Example shown is for
addressing the Sensitivity register. After addressing desired code,
cycle the supply to reset the bit field or apply a blow pulse to make the
parameter value permanent.
Programming Modes
Low-Noise Programmable Linear Hall Effect Sensor ICs with
Adjustable Bandwidth (50 kHz Maximum) and Analog Output
18
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
相關PDF資料 |
PDF描述 |
|---|---|
| A150N50X4A | 0 MHz - 2700 MHz 50 ohm RF/MICROWAVE TERMINATION |
| A15QS1-2 | FAST BLOW ELECTRIC FUSE, 1A, 150VAC, 150VDC, 100000A (IR), INLINE/HOLDER |
| A15QS10-2 | FAST BLOW ELECTRIC FUSE, 10A, 150VAC, 150VDC, 100000A (IR), INLINE/HOLDER |
| A15QS100-4TI | FAST BLOW ELECTRIC FUSE, 100A, 150VAC, 150VDC, 100000A (IR), INLINE/HOLDER |
| A15QS100-4 | FAST BLOW ELECTRIC FUSE, 100A, 150VAC, 150VDC, 100000A (IR), INLINE/HOLDER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A1362LKTTN-T | 功能描述:IC HALL EFFECT SENSOR LN 4-SIP RoHS:是 類別:傳感器，轉換器 >> 磁性 - 霍爾效應，數字式開關，線性，羅盤 (IC) 系列:- 標準包裝:1 系列:- 傳感范圍:20mT ~ 80mT 類型:旋轉 電源電壓:4.5 V ~ 5.5 V 電流 - 電源:15mA 電流 - 輸出（最大）:- 輸出類型:數字式，PWM，8.5 位串行 特點:可編程 工作溫度:-40°C ~ 150°C 封裝/外殼:20-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:20-SSOP 包裝:Digi-Reel® 其它名稱:AS5132-HSST-500DKR |
| A1363LKTTN-10-T | 功能描述:IC HALL SENSOR 6.4-14MV/G 4SIP 制造商:allegro microsystems, llc 系列:- 包裝:剪切帶（CT） 零件狀態:有效 類型:線性 技術:霍爾效應 軸:單路 感應范圍:- 電壓 - 電源:4.5 V ~ 5.5 V 電流 - 電源（最大值）:15mA 電流 - 輸出（最大值）:10mA 輸出類型:模擬電壓 分辨率:- 帶寬:120kHz 工作溫度:-40°C ~ 150°C（TA） 特性:可編程，溫度補償 封裝/外殼:4-SIP 模塊 供應商器件封裝:4-SIP 標準包裝:1 |
| A1363LKTTN-1-T | 功能描述:IC HALL SENSOR 0.6-1.3MV/G 4SIP 制造商:allegro microsystems, llc 系列:- 包裝:剪切帶（CT） 零件狀態:有效 類型:線性 技術:霍爾效應 軸:單路 感應范圍:- 電壓 - 電源:4.5 V ~ 5.5 V 電流 - 電源（最大值）:15mA 電流 - 輸出（最大值）:10mA 輸出類型:模擬電壓 分辨率:- 帶寬:120kHz 工作溫度:-40°C ~ 150°C（TA） 特性:可編程，溫度補償 封裝/外殼:4-SIP 模塊 供應商器件封裝:模塊 標準包裝:1 |
| A1363LKTTN-2-T | 功能描述:IC HALL SENSOR 1.3-2.9MV/G 4SIP 制造商:allegro microsystems, llc 系列:- 包裝:剪切帶（CT） 零件狀態:有效 類型:線性 技術:霍爾效應 軸:單路 感應范圍:- 電壓 - 電源:4.5 V ~ 5.5 V 電流 - 電源（最大值）:15mA 電流 - 輸出（最大值）:10mA 輸出類型:模擬電壓 分辨率:- 帶寬:120kHz 工作溫度:-40°C ~ 150°C（TA） 特性:可編程，溫度補償 封裝/外殼:4-SIP 模塊 供應商器件封裝:4-SIP 標準包裝:1 |
| A1363LKTTN-5-T | 功能描述:IC HALL SENSOR 2.9-6.4MV/G 4SIP 制造商:allegro microsystems, llc 系列:- 包裝:剪切帶（CT） 零件狀態:有效 類型:線性 技術:霍爾效應 軸:單路 感應范圍:- 電壓 - 電源:4.5 V ~ 5.5 V 電流 - 電源（最大值）:15mA 電流 - 輸出（最大值）:10mA 輸出類型:模擬電壓 分辨率:- 帶寬:120kHz 工作溫度:-40°C ~ 150°C（TA） 特性:可編程，溫度補償 封裝/外殼:4-SIP 模塊 供應商器件封裝:4-SIP 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。